參數資料
型號： M50FLW040A_06
廠商： 意法半導體
英文描述： 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
中文描述： 4兆位（5】64字節塊3】16】4 Kbyte的）3 - V電源供電固件集線器/低引腳數的閃存
文件頁數： 27/64頁
文件大?。?/td> 338K
代理商： M50FLW040A_06
M50FLW040A, M50FLW040B
Command interface
27/64
4.0.2
Read Status Register command
The Read Status Register command is used to read the Status Register. One Bus Write
cycle is required to issue the Read Status Register command. Once the command is issued,
subsequent Bus Read operations read the Status Register until another command is issued.
See the section on the Status Register for details on the definitions of the Status Register
bits.
4.0.3
Read Electronic Signature command
The Read Electronic Signature command is used to read the Manufacturer Code and the
Device Code. One Bus Write cycle is required to issue the Read Electronic Signature
command. Once the command is issued, the Manufacturer Code and Device Code can be
read using conventional Bus Read operations, and the addresses shown in
Table 12
.
Table 12.
The device remains in this mode until another command is issued. That is, subsequent Bus
Read operations continue to read the Manufacturer Code, or the Device Code, and not the
Memory Array.
4.0.4
Program command
The Program command can be used to program a value to one address in the memory array
at a time.
The Program command works by changing appropriate bits from ‘1’ to ‘0’. (It cannot change
a bit from ‘0’ back to ‘1’. Attempting to do so will not modify the value of the bit. Only the
Erase command can set bits back to ‘1’. and does so for all of the bits in the block.)
Two Bus Write operations are required to issue the Program command. The second Bus
Write cycle latches the address and data, and starts the Program/Erase Controller.
Once the command is issued, subsequent Bus Read operations read the value in the Status
Register. (See the section on the Status Register for details on the definitions of the Status
Register bits.)
If the address falls in a protected block, the Program operation will abort, the data in the
memory array will not be changed, and the Status Register will indicate the error.
During the Program operation, the memory will only accept the Read Status Register
command and the Program/Erase Suspend command. All other commands are ignored.
See
Figure 21
, for a suggested flowchart on using the Program command. Typical Program
times are given in
Table 18
.
Electronic signature codes
Code
Address
(1)
1.
A22 should be ‘1’, and the ID lines and upper address bits should be set according to the rules illustrated in
Table 5
,
Table 6
and
Table 8
.
Data
Manufacturer Code
...00000h
20h
Device Code
M50FLW040A
M50FLW040B
...00001h
08h
28h
相關PDF資料
PDF描述
M50FLW040AK5G 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
M50FLW040AK5P 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
M50FLW040AK5TG 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
M50FLW040AK5TP 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
M50FLW040AN5G 4-Mbit (5 】 64 Kbyte blocks + 3 】 16 】 4 Kbyte sectors) 3-V supply Firmware Hub / low-pin count Flash memory
相關代理商/技術參數
參數描述
M50FLW040AK1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory
M50FLW040AK1G 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory
M50FLW040AK1P 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory
M50FLW040AK1T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory
M50FLW040AK1TG 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit (5 x 64KByte Blocks + 3 x 16 x 4KByte Sectors) 3V Supply Firmware Hub / Low Pin Count Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*