- 您現在的位置：買賣IC網 > PDF目錄67775 > M41T56M6F (STMICROELECTRONICS) 0 TIMER(S), REAL TIME CLOCK, PDSO8 PDF資料下載
參數資料
| 型號： | M41T56M6F |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封裝： | 0.150 INCH, LEAD FREE, PLASTIC, SOP-8 |
| 文件頁數： | 2/25頁 |
| 文件大?。?/td> | 230K |
| 代理商： | M41T56M6F |
Operation
M41T56
2.2
Read mode
In this mode, the master reads the M41T56 slave after setting the slave address (see
Figure 7 on page 11 and Figure 8 on page 11). Following the WRITE Mode Control Bit (R/W
= 0) and the Acknowledge Bit, the word address An is written to the on-chip address pointer.
Next the START condition and slave address are repeated, followed by the READ Mode
Control Bit (R/W = 1). At this point, the master transmitter becomes the master receiver. The
data byte which was addressed will be transmitted and the master receiver will send an
Acknowledge Bit to the slave transmitter. The address pointer is only incremented on
reception of an Acknowledge Bit. The M41T56 slave transmitter will now place the data byte
at address An + 1 on the bus. The master receiver reads and acknowledges the new byte
and the address pointer is incremented to An + 2. This cycle of reading consecutive
addresses will continue until the master receiver sends a STOP condition to the slave
transmitter.
An alternate READ mode may also be implemented, whereby the master reads the M41T56
slave without first writing to the (volatile) address pointer. The first address that is read is the
last one stored in the pointer, see Figure 9 on page 11.
Table 2.
AC characteristics
Symbol
Parameter(1)
1.
Valid for ambient operating temperature: TA = –40 to 85°C; VCC = 4.5 to 5.5V (except where noted).
Min
Max
Unit
fSCL
SCL clock frequency
0
100
kHz
tLOW
Clock low period
4.7
s
tHIGH
Clock high period
4
s
tR
SDA and SCL rise time
1
s
tF
SDA and SCL fall time
300
ns
tHD:STA
START condition hold time
(after this period the first clock pulse is generated)
4s
tSU:STA
START condition setup time
(only relevant for a repeated start condition)
4.7
s
tSU:DAT
Data setup time
250
ns
tHD:DAT
(2)
2.
Transmitter must internally provide a hold time to bridge the undefined region (300ns max.) of the falling
edge of SCL.
Data hold time
0
s
tSU:STO
STOP condition setup time
4.7
s
tBUF
Time the bus must be free before a new
transmission can start
4.7
s
相關PDF資料 |
PDF描述 |
|---|---|
| M41T56MH6 | 0 TIMER(S), REAL TIME CLOCK, PDSO28 |
| M41T56M6 | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| M41T81M6TR | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
| M41T81M6 | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
| M41T94MQ6E | 1 TIMER(S), REAL TIME CLOCK, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M41T56M6TR | 功能描述:實時時鐘 Serial RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T56MH | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:512 bit 64b x8 Serial Access TIMEKEEPER SRAM |
| M41T56MH6 | 功能描述:實時時鐘 Serial 512 (64x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T56MH6E | 功能描述:實時時鐘 Serial 512 (64x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T56MH6F | 功能描述:實時時鐘 Serial 512 (64x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。