- 您現在的位置：買賣IC網 > PDF目錄45048 > M38D24G6FP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | M38D24G6FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 27/136頁 |
| 文件大?。?/td> | 2856K |
| 代理商： | M38D24G6FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁
Rev.3.02
Apr 10, 2008
Page 122 of 131
REJ03B0177-0302
38D2 Group
Notes on Timers
1. Frequency Divider
All timers shares one circuit for the frequency divider to generate
the count source.
Thus the frequency divider is not initialized when each
individual timer is activated. When the frequency divider is
selected as the count source, a one-cycle delay of the maximum
count source will result between when the timer is activated and
when it starts counting or outputs the waveform.
The count source cannot be observed externally.
2. Division Ratio for Timer 1 to 4
3. Switching Frequency and Count Source for Timer 1
to 4, X, and Y
Switch the frequency division or count source* while the timer
count is stopped.
*This also applies when the frequency divider output is selected
as the timer count source and the count source is switched in
conjunction with a transition between operating modes (on-
chip oscillator mode, XIN mode, or low-speed mode). Be
careful when changing settings in the CPU mode register.
4. Setting Timer 1 and 2 When STP Instruction
Executed
Before executing the STP instruction, first set the wait time at
return.
5. Setting Order to Timer 1 to 4
When switching the count source of timer 1 to timer 4, a narrow
pulse may be generated at the count input, which causes the timer
count value to be undefined. Also, if the timers are used in
cascade connection, a narrow pulse may be generated at the
output when writing to the pervious timer, which causes the next
timer count value to be undefined.
Thus set the value from timer 1 in order after setting the count
source of timer 1 to timer 4.
6. Write to Timer 2, 3, and 4
When writing to the latch only, if the write timing to the reload
latch and the underflow timing are almost the same, the value is
set into the timer and the timer latch at the same time. At this
time, count is stopped during write operation to the reload latch.
7. Timer 3 PWM0 Mode, Timer 4 PWM1 Mode
(1) When PWM output is suspended once it starts, the time to
resume outputting may be delayed one section (256
× ts) of
the short interval depending on the level of the output pulse
at that time:
Stop at “H”: No output delay
Stop at “L”: Output is delayed time of 256
× ts
(2) When PWM mode is used, the interrupt requests and values
of timer 3 and timer 4 are updated every cycle of the long
interval (4
× 256 × ts).
8. Write Order to Timer X
(1) When timer mode, pulse output mode, event counter mode,
or pulse width measurement mode is set, write to the
following registers in the order below:
The timer X register (extension)
The timer X register (low-order)
The timer X register (high-order)
Writing to only one of these registers cannot be performed.
When either of the above modes is set and timer X operates
as a 16-bit counter, if the timer X register (extension) is never
set after a reset release, setting the timer X register
(extension) is not required. In that case, write the timer X
register (low-order) first and the timer X register (high-order)
next. However, once the timer X register (extension) is
written, note that the value is retained in the reload latch.
(2) Write to the timer X register by the 16-bit unit. Do not read
the timer X register while write operation is performed. If the
write operation is not completed, normal operation will not
be performed.
(3) When IGBT output mode or PWM mode is set, do not write
“1” to the timer X register (extension). If “1” has been
already written to the timer X register, be sure to write “0” to
the register before use.
Write to the following registers in the order below:
The compare registers 1, 2, 3 (high- and low-order)
The timer X register (extension)
The timer X register (low-order)
The timer X register (high-order)
The compare registers (high- and low-order) can be written
in either order. However, be sure to write both the compare
registers 1, 2, 3 and the timer X register at the same time.
9. Read Order to Timer X
(1) In all modes, read the following registers in the order below:
The timer X register (extension)
The timer X register (high-order)
The timer X register (low-order)
When reading the timer X register (extension) is not
required, read the timer X register (high-order) first and the
timer X register (low-order) next.
The read order to the compare registers 1, 2, 3 is not
specified.
(2) Read the timer X register in 16-bit units. Do not write to it
during read operation. If read operation is terminated in
progress, normal operation will not be performed.
相關PDF資料 |
PDF描述 |
|---|---|
| M38D24G4FP | 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64 |
| M38D59FFHP | 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP80 |
| M38D58G8HP | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PQFP80 |
| M38D59GFFP | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PQFP80 |
| M38D59FFHP | 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38D24G6FP#U0 | 功能描述:IC 740/38D2 MCU QZ-ROM 80QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| M38D24G6HP#U0 | 功能描述:IC 740/38D2 MCU QZ-ROM 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| M38D24G6XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38D24G6XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38D24G7XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。