參數資料
型號： M38C24M6-051HP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 52/63頁
文件大?。?/td> 1000K
代理商： M38C24M6-051HP
52
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is
“
1.
”
After a
reset, initialize flags which affect program execution. In particular, it
is essential to initialize the index X mode (T) and the decimal mode
(D) flags because of their effect on calculations.
Interrupts
The contents of the interrupt request bits do not change immediately
after they have been written. After writing to an interrupt request reg-
ister, execute at least one instruction before performing a BBC or
BBS instruction.
Decimal Calculations
To calculate in decimal notation, set the decimal mode flag (D) to
“
1,
”
then execute an ADC or SBC instruction. After executing an
ADC or SBC instruction, execute at least one instruction before
executing an SEC, CLC, or CLD instruction.
In decimal mode, the values of the negative (N), overflow (V), and
zero (Z) flags are invalid.
Timers
If a value n (between 0 and 255) is written to a timer latch, the
frequency division ratio is 1/(n+1).
The timers share the one frequency divider to generate the count
source. Accordingly, when each timer starts operating, initializing
the frequency divider is not executed. Therefore, when the frequency
divider is selected for the count source, the delay of the maximum
one cycle of the count source is generated until the timer starts
counting or the waveform is output from timer starts operating. Also,
the count source cannot be checked externally.
Multiplication and Division Instructions
The index X mode (T) and the decimal mode (D) flags do not affect
the MUL and DIV instruction.
The execution of these instructions does not change the contents
of the processor status register.
Ports
The contents of the port direction registers cannot be read. The fol-
lowing cannot be used:
The data transfer instruction (LDA, etc.)
The operation instruction when the index X mode flag (T) is
“
1
”
The addressing mode which uses the value of a direction register
as an index
The bit-test instruction (BBC or BBS, etc.) to a direction register
The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a
direction register.
Use instructions such as LDM and STA, etc., to set the port direction
registers.
Serial I/O
In clock synchronous serial I/O, if the receive side is using an exter-
nal clock and it is to output the S
RDY
signal, set the transmit enable
bit, the receive enable bit, and the S
RDY
output enable bit to
“
1.
”
Serial I/O continues to output the final bit from the T
X
D pin after trans-
mission is completed.
A-D Converter
The comparator uses internal capacitors whose charge will be lost if
the clock frequency is too low.
Therefore, make sure that f(X
IN
) is at least on 250 kHz (Note) during
an A-D conversion.
Note:
When the frequency divided by 2/4/8 is selected by the AD
conversion clock selection bits, the above frequency is multi-
plied by 2/4/8. Also, when the STP instruction is executed dur-
ing the A-D conversion, the A-D conversion is stopped imme-
diately, the A-D conversion completion bit is set to
“
1
”
, and the
interrupt request is generated.
LCD
When the LCD power input pin V
L3
is not used, connect it to V
CC
.
Instruction Execution Time
The instruction execution time is obtained by multiplying the number
of cycles shown in the list of machine instructions by the period of the
internal clock
φ
.
相關PDF資料
PDF描述
M38C24M4-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C24M4-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C24M6-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C24M6-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29FFFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38C24M6-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C24M6-XXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29FFAFP 制造商:Renesas Electronics Corporation 功能描述:
M38C29FFAFP#U0 功能描述:IC 740/38C2 MCU FLASH 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87
M38C29FFAHP 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 60K 64-LQFP - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*