參數資料
型號： M38857M8-XXXHP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80
封裝： 12 X 12 MM, 0.50 MM PITCH, PLASTIC, LQFP-80
文件頁數： 85/105頁
文件大?。?/td> 1403K
代理商： M38857M8-XXXHP
3885 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
77
Fig. 75 Block erase flowchart
Program Command (4016)
The program operation starts when the command code “4016” is writ-
ten in the first bus cycle. Then, if the address and data to program
are written in the 2nd bus cycle, program operation (data program-
ming and verification) will start.
Whether the write operation is completed can be confirmed by read-
_____
ing the status register or the RY/BY signal status. When the program
starts, the read status register mode is accessed automatically and
the content of the status register can be read out from the data bus
(D0–D7). The status register bit 7 (SR7) is set to “0” at the same time
the write operation starts and is returned to “1” upon completion of
the write operation. In this case, the read status register mode re-
mains active until the read array command (FF16) is written.
____
The RY/BY pin is “L” during write operation and “H” when the write
operation is completed as is the status register bit 7.
At program end, program results can be checked by reading the sta-
tus register.
Block Erase Command (2016/D016)
By writing the command code “2016” in the first bus cycle and the
confirmation command code “D016” in the second bus cycle that
follows to the block address of a flash memory block, the system
initiates a block erase (erase and erase verify) operation.
Whether the block erase operation is completed can be confirmed
____
by reading the status register or the RY/BY signal. At the same time
the block erase operation starts, the read status register mode is
automatically entered, so the content of the status register can be
read out. The status register bit 7 (SR7) is set to “0” at the same time
the block erase operation starts and is returned to “1” upon comple-
tion of the block erase operation. In this case, the read status regis-
ter mode remains active until the read array command (FF16) is writ-
ten.
____
The RY/BY pin is “L” during block erase operation and “H” when the
block erase operation is completed as is the status register bit 7.
After the block erase operation is completed, the status register can
be read out to know the result of the block erase operation. For de-
tails, refer to the section where the status register is detailed.
Fig. 74 Page program flowchart
Start
Write 4016
Status register
read
Program
completed
NO
YES
Write address
Write data
SR4=0?
Program
error
NO
YES
SR7=1?
or
RY/BY=1?
Write
In this case, the read status
register mode remains
active until the read array
command (FF16) is written.
Write 2016
D016
Block address
Erase completed
NO
YES
Start
Write
SR5=0?
Erase error
YES
NO
SR7=1?
or
RY/BY=1?
Status register
read
In this case, the read status
register mode remains active
until the read array command
(FF16) is written.
相關PDF資料
PDF描述
M38858MC-XXXHP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80
M38867E8AFS 8-BIT, UVPROM, 5 MHz, MICROCONTROLLER, CQCC80
M38869MCA-XXXHP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80
M38869MFA-XXXGP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80
M38869MCA-XXXGP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
M38857M9-XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38857MA-XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38857MB-XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38857MC-XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38857MD-XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*