- 您現在的位置：買賣IC網 > PDF目錄370954 > M38507E8FP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38507E8FP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 55/86頁 |
| 文件大小： | 1193K |
| 代理商： | M38507E8FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁當前第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
55
3850 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Standard serial I/O mode
The standard serial I/O mode inputs and outputs the software com-
mands, addresses and data needed to operate (read, program,
erase, etc.) the internal flash memory. This I/O is clock synchronized
serial. This modes require a purpose-specific peripheral unit.
The standard serial I/O mode is different from the parallel I/O mode
in that the CPU controls flash memory rewrite (uses the CPU's re-
write mode), rewrite data input and so forth. The standard serial I/O
mode is started by connecting
“
H
”
to the P4
1
(INT
0
) pin and
“
H
”
to the
CNV
SS
pin (when V
CC
= 4.5 V to 5.5 V, connect to V
CC
; when V
CC
=
2.7 V to 4.5 V, supply 4.5 V to 5.5 V to Vpp from an external source),
and releasing the reset operation. (In the ordinary command mode,
set CNVss pin to
“
L
”
level.)
This control program is written in the boot ROM area when the prod-
uct is shipped from Mitsubishi. Accordingly, make note of the fact
that the standard serial I/O mode cannot be used if the boot ROM
area is rewritten in the parallel I/O mode. Figure 56 shows the pin
connections for the standard serial I/O mode. Serial data I/O uses SI/
O1 data serially in 8-bit units.
To use standard serial I/O mode. The operation uses the four SI/O1
pins S
CLK
, RxD, TxD and S
RDY1
(BUSY). The S
CLK
pin is the trans-
fer clock input pin through which an external transfer clock is input.
The TxD pin is for CMOS output. The S
RDY1
(BUSY) pin outputs an
“
L
”
level when ready for reception and an
“
H
”
level when reception
starts.
In the standard serial I/O mode, only the user ROM area indicated in
Figure 44 can be rewritten. The boot ROM cannot.
In the standard serial I/O mode, a 7-byte ID code is used. When
there is data in the flash memory, commands sent from the periph-
eral unit (programmer) are not accepted unless the ID code
matches.
Overview of standard serial I/O mode
In standard serial I/O mode, software commands, addresses and
data are input and output between the MCU and peripheral units
(serial programer, etc.) using 4-wire clock-synchronized serial I/O
(SI/O1).
In reception, software commands, addresses and program data are
synchronized with the rise of the transfer clock that is input to the
S
CLK
pin, and are then input to the MCU via the RxD pin. In transmis-
sion, the read data and status are synchronized with the fall of the
transfer clock, and output from the TxD pin.
The TxD pin is for CMOS output. Transfer is in 8-bit units with LSB
first.
When busy, such as during transmission, reception, erasing or pro-
gram execution, the S
RDY1
(BUSY) pin is
“
H
”
level. Accordingly, al-
ways start the next transfer after the S
RDY1
(BUSY) pin is
“
L
”
level.
Also, data and status registers in memory can be read after inputting
software commands. Status, such as the operating state of the flash
memory or whether a program or erase operation ended success-
fully or not, can be checked by reading the status register. Here fol-
lowing are explained software commands, status registers, etc.
相關PDF資料 |
PDF描述 |
|---|---|
| M38503E4SS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38503M4 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38503MXH | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38507E8SP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38503M4H-XXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38507F8AFP#U1 | 功能描述:IC 740/3850 MCU FLASH 42SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38507F8AFP#W1 | 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 32K PB-FREE 42-SSOP T&R - Tape and Reel |
| M38507F8FP | 制造商:Renesas Electronics Corporation 功能描述:MCU 8-Bit 740 CISC 32KB Flash 5V 42-Pin SSOP 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays |
| M38507F8FP#U1 | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays |
| M38507F8FP#W1 | 制造商:Renesas Electronics Corporation 功能描述:FLASH 8-BIT 2.7 TO 5.5V PBFREE |
發布緊急采購，3分鐘左右您將得到回復。