- 您現在的位置：買賣IC網 > PDF目錄296384 > M38225MCHFP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38225MCHFP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 15/78頁 |
| 文件大?。?/td> | 998K |
| 代理商： | M38225MCHFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
22
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
3822 Group
MITSUBISHI MICROCOMPUTERS
INTERRUPTS
Interrupts occur by seventeen sources: eight external, eight inter-
nal, and one software.
Interrupt Control
Each interrupt is controlled by an interrupt request bit, an interrupt
enable bit, and the interrupt disable flag except for the software
interrupt set by the BRK instruction. An interrupt occurs if the cor-
responding interrupt request and enable bits are “1” and the
interrupt disable flag is “0”.
Interrupt enable bits can be set or cleared by software.
Interrupt request bits can be cleared by software, but cannot be
set by software.
The BRK instruction cannot be disabled with any flag or bit. The I
flag disables all interrupts except the BRK instruction interrupt.
When several interrupts occur at the same time, the interrupts are
received according to priority.
Interrupt Operation
Upon acceptance of an interrupt the following operations are auto-
matically performed:
1. The contents of the program counter and processor status
register are automatically pushed onto the stack.
2. The interrupt disable flag is set and the corresponding
interrupt request bit is cleared.
3. The interrupt jump destination address is read from the vec-
tor table into the program counter.
sNotes on interrupts
When setting the followings, the interrupt request bit may be set to
“1”.
When setting external interrupt active edge
Related register: Interrupt edge selection register (address 3A16)
Timer X mode register (address 2716)
Timer Y mode register (address 2816)
When switching interrupt sources of an interrupt vector address
where two or more interrupt sources are allocated
Related register: A-D control regsiter (address 3416)
When not requiring for the interrupt occurrence synchronized with
these setting, take the following sequence.
Set the corresponding interrupt enable bit to “0” (disabled).
Set the interrupt edge select bit or the interrupt source select bit
to “1”.
Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
Set the corresponding interrupt enable bit to “1” (enabled).
Notes1: Vector addresses contain interrupt jump destination addresses.
2: Reset function in the same way as an interrupt with the highest priority.
Table 10 Interrupt vector addresses and priority
Remarks
Interrupt Request
Generating Conditions
At reset
At detection of either rising or
falling edge of INT0 input
At detection of either rising or
falling edge of INT1 input
At completion of serial I/O data
reception
At completion of serial I/O trans-
mit shift or when transmission
buffer is empty
Interrupt Source
Low
High
Priority
Vector Addresses (Note 1)
Reset (Note 2)
INT0
INT1
Serial I/O
reception
Serial I/O
transmission
Timer X
Timer Y
Timer 2
Timer 3
CNTR0
CNTR1
Timer 1
INT2
INT3
Key input
(Key-on wake-up)
ADT
A-D conversion
BRK instruction
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
FFFD16
FFFB16
FFF916
FFF716
FFF516
FFF316
FFF116
FFEF16
FFED16
FFEB16
FFE916
FFE716
FFE516
FFE316
FFE116
FFDF16
FFDD16
FFFC16
FFFA16
FFF816
FFF616
FFF416
FFF216
FFF016
FFEE16
FFEC16
FFEA16
FFE816
FFE616
FFE416
FFE216
FFE016
FFDE16
FFDC16
At timer X underflow
At timer Y underflow
At timer 2 underflow
At timer 3 underflow
At detection of either rising or
falling edge of CNTR0 input
At detection of either rising or
falling edge of CNTR1 input
At timer 1 underflow
At detection of either rising or
falling edge of INT2 input
At detection of either rising or
falling edge of INT3 input
At falling of conjunction of input
level for port P2 (at input mode)
At falling of ADT input
At completion of A-D conversion
At BRK instruction execution
Non-maskable
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
Valid when serial I/O is selected
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
External interrupt
(active edge selectable)
External interrupt
(Valid at falling)
Valid when ADT interrupt is se-
lected, External interrupt
(Valid at falling)
Valid when A-D interrupt is se-
lected
Non-maskable software interrupt
相關PDF資料 |
PDF描述 |
|---|---|
| M38225MAXXXFS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38225MAXXXGP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38226MCMFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38226E1FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38226E1FS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38227ECFP | 功能描述:IC 740 MCU EPROM 48K 80QFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38227ECFP#U0 | 功能描述:MCU 3/5V 48K PB-FREE 80-QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| M38227ECFS | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 48KB EPROM 5V 80CLCC - Bulk |
| M38227FGFP | 制造商:Renesas Electronics Corporation 功能描述:SLIM740 OTP 16K/512B RAM, W/A-D, LED, 4 - Rail/Tube |
| M38227RFS | 制造商:Renesas Electronics Corporation 功能描述:MCU - Trays |
發布緊急采購，3分鐘左右您將得到回復。