參數資料
型號： M38198M7-XXXFS
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 16/60頁
文件大?。?/td> 664K
代理商： M38198M7-XXXFS
16
3819 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
INTERRUPTS
Interrupts occur by 20 sources: 5 external, 14 internal, and 1 soft-
ware.
Interrupt Control
Each interrupt is controlled by an interrupt request bit, an interrupt
enable bit, and the interrupt disable flag except for the software in-
terrupt set by the BRK instruction. An interrupt occurs if the
corresponding interrupt request and enable bits are “1” and the in-
terrupt disable flag is “0”.
Interrupt enable bits can be set or cleared by software.
Interrupt request bits can be cleared by software, but cannot be
set by software.
The BRK instruction cannot be disabled with any flag or bit.
The I (interrupt disable) flag disables all interrupts except the BRK
instruction interrupt.
Interrupt Operation
When an interrupt is received, the contents of the program counter
and processor status register are automatically stored into the
stack. The interrupt disable flag is set to inhibit other interrupts
from interfering. The corresponding interrupt request bit is cleared
and the interrupt jump destination address is read from the vector
table into the program counter.
Notes on Use
When the active edge of an external interrupt (INT
0
to INT
4
) is
changed or when switching interrupt sources in the same vector
address, the corresponding interrupt request bit may also be set.
Therefore, please take following sequence;
(1) Disable the external interrupt which is selected.
(2) Change the active edge.
(3) Clear the interrupt request bit which is selected to “0”.
(4) Enable the external interrupt which is selected.
Table 1. Interrupt vector addresses and priority
Interrupt Request
Generating Conditions
High
FFFD
16
Interrupt Source
Priority
Low
FFFC
16
Remarks
Reset (Note 2)
Non-maskable
External interrupt (active edge
selectable)
External interrupt (active edge
selectable)
External interrupt (active edge
selectable)
Valid when interrupt interval
determination is operating
Valid when serial I/O ordinary
mode is selected
Valid when serial I/O automatic
transfer mode is selected
Valid when serial I/O2 is se-
lected
Valid when serial I/O3 is se-
lected
STP release timer underflow
1
Notes 1 :
Vector addresses contain interrupt jump destination addresses.
2 :
Reset function in the same way as an interrupt with the highest priority.
Vector Addresses (Note 1)
At reset
At detection of either rising or
falling edge of INT
0
input
At detection of either rising or
falling edge of INT
1
/ZCR input
At detection of either rising or
falling edge of INT
2
input
INT
0
INT
1
/ZCR
INT
2
Remote control/
counter overflow
Serial I/O1
Serial I/O
automatic transfer
Serial I/O2
Serial I/O3
Timer 1
Timer 2
Timer 3
Timer 4
Timer 5
Timer 6
INT
3
2
3
At 8-bit counter overflow
At completion of data transfer
At completion of the last data
transfer
At completion of data transfer
At completion of data transfer
At timer 1 underflow
At timer 2 underflow
At timer 3 underflow
At timer 4 underflow
At timer 5 underflow
At timer 6 underflow
At detection of either rising or
falling edge of INT
3
input
External interrupt (active edge
selectable)
Valid when INT
4
interrupt is
selected
External interrupt (active
edge selectable)
Valid when A-D conversion in-
terrupt is selected
At detection of either rising or
falling edge of INT
4
input
At completion of A-D conver-
sion
At falling edge of the last digit
immediately before blanking
period starts
At rising edge of each digit
At BRK instruction execution
Valid when FLD blanking in-
terrupt is selected
Valid when FLD digit interrupt
is selected
Non-maskable software inter-
rupt
FFFA
16
FFF8
16
FFF6
16
FFF4
16
FFF2
16
FFF0
16
FFEE
16
FFEC
16
FFEA
16
FFE8
16
FFE6
16
FFE4
16
FFE2
16
FFE0
16
FFDE
16
FFDC
16
FFFB
16
FFF9
16
FFF7
16
FFF5
16
FFF3
16
FFF1
16
FFEF
16
FFED
16
FFEB
16
FFE9
16
FFE7
16
FFE5
16
FFE3
16
FFE1
16
FFDF
16
FFDD
16
4
5
6
7
8
9
10
11
12
13
14
15
16
17
INT
4
A-D conversion
FLD blanking
FLD digit
BRK instruction
相關PDF資料
PDF描述
M38198M8-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38198M8-XXXFS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38198M9-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38198M9-XXXFS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38198MC-053 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38198MCA809 制造商:Panasonic Industrial Company 功能描述:IC
M38198MCA824 制造商:Panasonic Industrial Company 功能描述:IC
M38198MCA827 制造商:Panasonic Industrial Company 功能描述:IC
M38199MF072F 制造商:Panasonic Industrial Company 功能描述:IC
M38199MF210F 制造商:Panasonic Industrial Company 功能描述:IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*