- 您現在的位置：買賣IC網 > PDF目錄370902 > M38198M7-XXXFP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38198M7-XXXFP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 50/60頁 |
| 文件大?。?/td> | 664K |
| 代理商： | M38198M7-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
50
3819 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is “1”. Af-
ter a reset, initialize flags which affect program execution. In
particular, it is essential to initialize the index X mode (T) and the
decimal mode (D) flags because of their effect on calculations.
Interrupts
The contents of the interrupt request bits do not change immedi-
ately after they have been written. After writing to an interrupt
request register, execute at least one instruction before performing
a BBC or BBS instruction.
Decimal Calculations
To calculate in decimal notation, set the decimal mode flag (D)
to “1”, then execute an ADC or SBC instruction. Only the ADC
and SBC instructions yield proper decimal results. After execut-
ing an ADC or SBC instruction, execute at least one instruction
before executing a SEC, CLC, or CLD instruction.
In decimal mode, the values of the negative (N), overflow (V),
and zero (Z) flag are invalid.
The carry flag can be used to indicate whether a carry or borrow
has occurred. Initialize the carry flag before each calculation.
Clear the carry flag before an ADC and set the flag before an
SBC.
Timers
If a value n (between 0 and 255) is written to a timer latch, the fre-
quency division ratio is 1/(n+1).
Multiplication and Division Instructions
The index X mode (T) and the decimal mode (D) flags do not af-
fect the MUL and DIV instruction.
The execution of these instructions does not change the con-
tents of the processor status register.
Ports
The contents of the port direction registers cannot be read. The
following cannot be used:
the data transfer instruction (LDA, etc.)
the operation instruction when the index X mode flag (T) is “1”
the addressing mode which uses the value of a direction register
as an index
the bit-test instruction (BBC or BBS, etc.) to a direction register
the read-modify-write instructions (ROR, CLB, or SEB, etc.) to a
direction register.
Use instructions such as LDM and STA, etc., to set the port direc-
tion registers.
Serial I/O
When using an external clock, input “H” to the external clock input
pin and clear the serial I/O interrupt request bit before executing
serial I/O transfer and serial I/O automatic transfer.
When using the internal clock, set the synchronous clock to inter-
nal clock, then clear the serial I/O interrupt request bit before
executing a serial I/O transfer and serial I/O automatic transfer.
A-D Converter
The comparator uses internal capacitors whose charge will be lost
if the clock frequency is too low.
Make sure that f(X
IN
) is 500 kHz or more during an A-D conver-
sion.
Do not execute the STP or WIT instruction during an A-D conver-
sion.
Instruction Execution Time
The instruction execution time is obtained by multiplying the fre-
quency of the internal clock
φ
by the number of cycles needed to
execute an instruction.
The number of cycles required to execute an instruction is shown
in the list of machine instructions. The frequency of the internal
clock
φ
is half of the X
IN
or X
CIN
frequency.
At the STP Instruction Release
At the STP instruction release, all bits of the timer 12 mode regis-
ter are cleared.
The X
COUT
drivability selection bit (the CPU mode register) is set
to “1” (high drive) in order to start oscillating.
相關PDF資料 |
PDF描述 |
|---|---|
| M38198M7-XXXFS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38198M8-XXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38198M8-XXXFS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38198M9-XXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38198M9-XXXFS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38198MCA809 | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38198MCA824 | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38198MCA827 | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38199MF072F | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38199MF210F | 制造商:Panasonic Industrial Company 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。