參數資料
型號: M38191E1-XXXFP
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述: 單芯片8位CMOS微機
文件頁數: 47/60頁
文件大?。?/td> 664K
代理商: M38191E1-XXXFP
47
3819 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
CLOCK GENERATING CIRCUIT
The 3819 group has two built-in oscillation circuits. An oscillation
circuit can be formed by connecting a resonator between X
IN
and
X
OUT
(X
CIN
and X
COUT
). Use the circuit constants in accordance
with the resonator manufacturer's recommended values. No exter-
nal resistor is needed between X
IN
and X
OUT
since a feed-back
resistor exists on-chip. However, an external feed-back resistor is
needed between X
CIN
and X
COUT
.
Immediately after poweron, only the X
IN
oscillation circuit starts
oscillation, and X
CIN
and X
COUT
pins function as I/O ports.
Frequency Control
Middle-speed mode
The internal clock
φ
is the frequency of X
IN
divided by 8. After re-
set, this mode is selected.
High-speed mode
The internal clock
φ
is half the frequency of X
IN
.
Low-speed mode
The internal clock
φ
is half the frequency of X
CIN
.
Note :
If you switch the mode between middle/high-speed and low-speed,
stabilize both X
IN
and X
CIN
oscillations. The sufficient time is re-
quired for the X
CIN
oscillation to stabilize, especially immediately
after poweron and at returning from stop mode. When switching the
mode between middle/high-speed and low-speed, set the frequency
on condition that f(X
IN
) > 3·f(X
CIN
).
Low-power dissipation mode
When stopping the main clock X
IN
in the low-speed mode, the low-
power dissipation operation starts. To stop the main clock, set the
bit 5 of the CPU mode register to “1”. When the main clock X
IN
is
restarted, set enough time for oscillation to stabilize by program-
ming.
The low-power dissipation operation 200
μ
A or less (at f(X
IN
) = 32
kHz) can be realized by reducing the X
CIN
–X
COUT
drivability. To re-
duce the X
CIN
–X
COUT
drivability, clear the bit 3 of the CPU mode
register to “0”. At reset or when executing the STP instruction, this
bit is set to “1” and strong drivability is selected to help the oscilla-
tion to start.
Oscillation Control
Stop mode
If the STP instruction is executed, the internal clock
φ
stops at an
“H” level, and X
IN
and X
CIN
oscillators stop. Timer 1 is set to “FF
16
and timer 2 is set to “01
16
”. Either X
IN
or X
CIN
divided by 16 is in-
put to timer 1, and the output of timer 1 is connected to timer 2.
The bits of the timer 12 mode register are cleared to “0”. Set the
timer 1 and timer 2 interrupt enable bits to disabled (“0”) before ex-
ecuting the STP instruction.
Oscillator restarts at reset or when an external interrupt is re-
ceived, but the internal clock
φ
is not supplied to the CPU until
timer 1 underflows. When using an external resonator, it is neces-
sary for oscillating to stabilize.
Wait mode
If the WIT instruction is executed, the internal clock
φ
stops at an
“H” level. The states of X
IN
and X
CIN
are the same as the state be-
fore executing the WIT instruction. The internal clock restarts at
reset or when an interrupt is received. Since the oscillator does
not stop, normal operation can be started immediately after the
clock is restarted.
Fig. WA-1 Ceramic resonator external circuit
Fig. WA-2 External clock input circuit
X
CIN
X
COUT
C
CIN
C
COUT
R
d
R
f
X
IN
X
OUT
C
IN
C
OUT
X
CIN
X
COUT
X
IN
X
OUT
Open
Open
External oscillation
circuit or pulse
External oscillation
circuit
V
CC
V
SS
V
CC
V
SS
相關PDF資料
PDF描述
M38191E1-XXXFS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38191E2-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38191E2-XXXFS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38194EA-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38194EA-XXXFS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38197MA127F 制造商:Panasonic Industrial Company 功能描述:IC
M38197MA131F 制造商:Panasonic Industrial Company 功能描述:IC
M38197MA137F 制造商:Panasonic Industrial Company 功能描述:IC
M38197MA161F 制造商:Panasonic Industrial Company 功能描述:IC
M38197MA181F 制造商:Panasonic Industrial Company 功能描述:IC