參數資料
型號： M38001S7-XXXFS
廠商： Mitsubishi Electric Corporation
英文描述： Shelf; External Depth:16"; External Width:22"; Color:Gray
中文描述： 8位單片機
文件頁數： 120/173頁
文件大?。?/td> 4203K
代理商： M38001S7-XXXFS
3800 GROUP USER’S MANUAL
3-18
APPENDIX
3.3 Notes on use
(1) Sequence for switching an external interrupt
detection edge
When the external interrupt detection edge must be
switched, make sure the following sequence.
Clear an interrupt enable bit to “0” (interrupt disabled)
Switch the detection edge
Clear an interrupt request bit to “0” (no interrupt requ-
est issued)
Set the interrupt enable bit to “1” ( interrupt enabled )
3.3 Notes on use
3.3.1 Notes on interrupts
Reason
The interrupt circuit recognizes the switching of the
detection edge as the change of external input
signals. This may cause an unnecessary interrupt.
(2) Bits 7 and 6 of the interrupt control register 2
Fix the bits 7 and 6 of the interrupt control register 2
(Address:003F
16
) to “0”.
Figure 3.3.1 shows the structure of the interrupt
control register 2.
Fig. 3.3.1 Structure of interrupt control register 2
3.3.2 Notes on the serial I/O
(1) Stop of data transmission
As for the serial I/O that can be used as either a clock synchronous or an asynchronous (UART) serial I/O, clear
the transmit enable bit to “0” (transmit disabled), and clear the serial I/O enable bit to “0” (serial I/O disabled)in the
following cases :
G
when stopping data transmission during transmitting data in the clock synchronous serial I/O mode
G
when stopping data transmission during transmitting data in the UART mode
G
when stopping only data transmission during transmitting and receiving data in the UART mode
Reason
Since transmission is not stopped and the transmission circuit is not initialized even if the serial I/O enable bit is
cleared to “0” (serial I/O disabled), the internal transmission is running (in this case, since pins TxD, RxD, S
CLK
,
and S
RDY
function as I/O ports, the transmission data is not output). When data is written to the transmit buffer
register in this state, the data is transferred to the transmit shift register and start tp be sjifted. When the serial
I/O enable bit is set to “1” at this time, the data during internally shifting is output to the TxD pin and ti may cause
an operation failure to a microcomputer.
(2) Stop of data reception
As for the serial I/O that can be used as either a clock synchronous or an asynchronous (UART) serial I/O, clear
the receive enable bit to “0” (receive disabled), or clear the serial I/O enable bit to “0” (serial I/O disabled) in the
following case :
G
when stopping data reception during receiving data in the clock synchronous serial I/O mode
Clear the receive enable bit to “0” (receive disabled) in the following cases :
G
when stopping data reception during receiving data in the UART mode
G
when stopping only data reception during transmitting and receiving data in the UART mode
b7
0 0
b0
Interrupt control register 2
Address 003F
16
Interrupt enable bits
Not used
Fix these bits to “0”.
相關PDF資料
PDF描述
M38001S7-XXXHP 1 watt dc-dc converters
M38001S7-XXXSS 1 watt dc-dc converters
M38003M1-XXXSP 1 watt dc-dc converters
M38004E1-XXXSP 1 watt dc-dc converters
M38001S1-XXXSP 1 watt dc-dc converters
相關代理商/技術參數
參數描述
M38001S7-XXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38001S7-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38001S7-XXXSS 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38001S8-DXXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 38000 SERIES
M38001S8-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*