- 您現在的位置：買賣IC網 > PDF目錄98007 > M37906F8CFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO42 PDF資料下載
參數資料
| 型號： | M37906F8CFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO42 |
| 封裝： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件頁數： | 5/34頁 |
| 文件大?。?/td> | 253K |
| 代理商： | M37906F8CFP |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
16-BIT CMOS MICROCOMPUTER
M37906F8CFP, M37906F8CSP
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e param
etric
lim
its are
subject
to change.
13
Flash Memory Parallel I/O Mode
The flash memory parallel I/O mode is used to manipulate the inter-
nal flash memory with a parallel programmer. This parallel program-
mer uses the software commands listed in Table 1 to do the flash
memory manipulations, such as read/programming/erase opera-
tions.
Table 1. Software commands (flash memory parallel I/O mode)
Software Command
Read Array
Read Status Register
Clear Status Register
Programming
Block Erase
Erase All Block
User ROM Area and Boot ROM Area
The user ROM area and boot ROM area can be reprogrammed in
the flash memory parallel I/O mode.
The programming and block erase operations can be performed only
to these areas.
The boot ROM area, 8 Kbytes in size, is assigned to addresses
000016–1FFF16, so that programming and block erase operations
can be performed only to this area. (Access to any address out of
this area is prohibited).
The erasable block in the boot ROM area is only one block, consist-
ing of 8 Kbytes. The reprogramming control firmware to be used in
the flash memory serial I/O mode has been stored to this boot ROM
area on our shipment. Therefore, do not reprogram the boot ROM
area if the user uses the flash memory serial I/O mode.
Do not program to addresses FF9016 to FF9F16 because this area is
the reserved area for the programmer.
Note that, when the boot ROM area is read out from the CPU in the
CPU reprogramming mode, described later, its addresses will be
shifted to E00016—FFFF16.
Addresses FF9016 to FF9F16 are the reserved area for the parallel
programmer. Therefore, when the user uses the flash memory paral-
lel I/O mode, do not program to this area.
相關PDF資料 |
PDF描述 |
|---|---|
| M37906F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 |
| M37920S4CGP | 16-BIT, 20 MHz, MICROCONTROLLER, PQFP100 |
| M38184E8-XXXFP | 8-BIT, OTPROM, 6.3 MHz, MICROCONTROLLER, PQFP100 |
| M38184EA-XXXFP | 8-BIT, OTPROM, 6.3 MHz, MICROCONTROLLER, PQFP100 |
| M38184EAFP | 8-BIT, OTPROM, 8.4 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37906F8CFP-T4 | 制造商:Renesas Electronics Corporation 功能描述:FLSH 16-BIT |
| M37906F8CSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M4C-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M4C-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M4H-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。