參數資料
型號： M37736EHLHP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, OTPROM, MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100
文件頁數： 42/63頁
文件大?。?/td> 8367K
代理商： M37736EHLHP
CENTRAL PROCESSING UNIT (CPU)
7733 Group User’s Manual
2–9
(5) Bit 4: Index register length flag (x)
This flag determines whether index register X or index register Y is used as a 16-bit register or an
8-bit register. The register is used as a 16-bit register when this flag is “0” and as an 8-bit register
when this flag is “1.” When setting this flag to “1,” execute the SEP instruction; when clearing this flag
to “0,” execute the CLP instruction.
At reset, this flag is cleared to “0.”
Note: When data is transferred between registers which are different in bit length, the data is transferred
with the bit length of the destination register. But this is not applied to the case where the TXA,
TYA, TXB, or TYB instruction is executed. Refer to “7700 Family Software Manual” for
details.
(6) Bit 5: Data length flag (m)
This flag determines whether data is used as 16-bit data or 8-bit data. Data is used as 16-bit data
when this flag is “0” and as 8-bit data when this flag is “1.” When setting this flag to “1,” execute the
SEM or SEP instruction; when clearing this flag to “0,” execute the CLM or CLP instruction.
At reset, this flag is cleared to “0.”
Note: When data is transferred between registers which are different in bit length, the data is transferred
with the data length of the destination register. But this is not applied to the case where the
TXA, TYA, TXB, or TYB instruction is executed. Refer to “7700 Family Software Manual” for
details.
(7) Bit 6: Overflow flag (V)
This flag is valid when addition or subtraction is executed for each word which is processed as signed
binary data. If the data length flag (m) is “0,” the overflow flag is set to “1” when the result of addition
or subtraction exceeds the range between –32768 and +32767 and cleared to “0” in the other cases.
If the data length flag (m) is “1,” the overflow flag is set to “1” when the result of addition or subtraction
exceeds the range between –128 and +127 and cleared to “0” in the other cases. Also, the overflow
flag is set to “1” when the length of the division result obtained by the DIV instruction is longer than
that of a register where the result is to be stored. When the BVC or BVS instruction is executed, the
program branches according to this flag’s state. This flag is ignored in the decimal mode. When setting
this flag to “1,” execute the SEP instruction; when clearing this flag to “0,” execute the CLV or CLP
instruction.
(8) Bit 7: Negative flag (N)
This flag is set to “1” when the result of an arithmetic operation or data transfer is negative. (Bit 15
of the result is “1” when the data length flag (m) is “0,” or bit 7 of the result is “1” when the data length
flag (m) is “1.”) It is cleared to “0” in the other cases. When the BPL or BMI instruction is executed,
the program branches according to this flag’s state. This flag is ignored in the decimal mode. When
setting this flag to “1,” execute the SEP instruction; when clearing this flag to “0,” execute the CLP
instruction.
(9) Bits 8 to 10: Processor interrupt priority level (IPL)
These bits can specify one of levels 0 to 7 as the processor interrupt priority level. An interrupt is
enabled when its interrupt priority level, which is set in the interrupt control register, is higher than IPL.
When the interrupt request is accepted, the contents of IPL is stored into the stack area and the
interrupt priority level of the accepted interrupt is set in IPL.
No instruction can directly set or clear each of these bits. When changing these bits, store a desired
processor interrupt priority level into the stack area. And then, change the contents of the processor
status register by executing the PUL or PLP instruction.
At reset, the contents of IPL is cleared to “0002.”
2.1 Central processing unit
相關PDF資料
PDF描述
M37735S4LHP 16-BIT, MICROCONTROLLER, PQFP80
M37735EHLHP 16-BIT, OTPROM, MICROCONTROLLER, PQFP80
M37753M6C-XXXFP 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP80
M37754M6C-XXXHP 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100
M37754M6C-XXXGP 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M37736EHLXXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:PROM VERSION OF M37736MHLXXXHP
M37736M4B 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37736M4BXXXGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37736M4L 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37736M4LXXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*