- 您現在的位置：買賣IC網 > PDF目錄370847 > M37641F8-XXXFP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37641F8-XXXFP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 146/149頁 |
| 文件大?。?/td> | 1997K |
| 代理商： | M37641F8-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁當前第146頁第147頁第148頁第149頁
146
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINARY
Notice: This is not a final specification.
change.
Some parametric limits are subject to
Oscillator Wiring (Noise Elimination)
(1) Keeping oscillator away from large current signal lines
Install a microcomputer (and especially an oscillator) as far as
possible from signal lines, including USB signal lines, where a cur-
rent larger than the tolerance of current value flows. When a large
current flows through those signal lines, strong noise occurs be-
cause of mutual inductance.
(2) Installing oscillator away from signal lines where potential
levels change frequently
Install an oscillator and a connecting pattern of an oscillator away
from signal lines where potential levels change frequently. Also, do
not cross such signal lines over the clock lines or the signal lines
which are sensitive to noise.
Terminate Unused Pins
(1) Output ports : Open
(2) Input ports :
Connect each pin to Vcc or Vss through each resistor of 1 k
to
10 k
.
Ports that permit the selecting of a built-in pull-up or pull-down re-
sistor can also use this resistor. As for pins whose potential affects
to operation modes such as pins CNVss, INT or others, select the
Vcc pin or the Vss pin according to their operation mode.
(3) I/O ports :
Set the I/O ports for the input mode and connect them to Vcc or
Vss through each resistor of 1 k
to 10 k
.
Ports that permit the selecting of a built-in pull-up or pull-down re-
sistor can also use this resistor. Set the I/O ports for the output
mode and open them at
“
L
”
or
“
H
”
.
When opening them in the output mode, the input mode of the
initial status remains until the mode of the ports is switched over
to the output mode by the program after reset. Thus, the potential
at these pins is undefined and the power source current may in-
crease in the input mode. With regard to an effects on the
system, thoroughly perform system evaluation on the user side.
Since the direction register setup may be changed because of a
program runaway or noise, set direction registers by program pe-
riodically to increase the reliability of program.
At the termination of unused pins, perform wiring at the shortest
possible distance (20 mm or less) from microcomputer pins.
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM produc-
tion:
1. Mask ROM Order Confirmation Form
2. Mark Specification Form
3. Data to be written to ROM, in EPROM form (three identical cop-
ies) or one floppy disk.
For the mask ROM confirmation and the mark specifications, refer
to the
“
Mitsubishi MCU Technical Information
”
Homepage:
http://www.infomicom.maec.co.jp
Clock Input/Output Pin Wiring (Noise
Elimination)
(1) Make the wiring for the input/output pins as short as possible.
(2) Make the wiring across the grounding lead of the capacitor
which is connected to an oscillator and the Vss pin of the MCU
as short as possible (within 20 mm)
(3) Make sure to isolate the oscillation Vss pattern from other pat-
terns for oscillation circuit-use only.
相關PDF資料 |
PDF描述 |
|---|---|
| M37641F8-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8-XXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641F8FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641F8HP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37641F8-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8-100FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8E8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。