- 您現在的位置：買賣IC網 > PDF目錄69014 > M37630E4T-XXXFP 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | M37630E4T-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | 0.80 MM PITCH, PLASTIC, QFP-44 |
| 文件頁數： | 6/48頁 |
| 文件大小： | 563K |
| 代理商： | M37630E4T-XXXFP |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
MITSUBISHI
ELECTRIC
14
MITSUBISHI MICROCOMPUTERS
7630 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
INTERRUPTS
There are 24 interrupts: 6 external, 17 internal, and 1 software.
Interrupt Control
Each interrupt except the BRK instruction interrupt has both an
interrupt request bit and an interrupt enable bit, and is controlled by
the interrupt disable flag. An interrupt occurs when the correspond-
ing interrupt request and enable bits are “1” and the interrupt dis-
able flag is “0”. Interrupt enable bits can be cleared or set by
software. Interrupt request bits can be cleared by software but can-
not be set by software. The BRK instruction interrupt and reset can-
not be disabled with any flag or bit. The I flag disables all interrupts
except the BRK instruction interrupt and reset. If several interrupt
requests occur at the same time, the interrupt with the highest prior-
ity is accepted first.
Interrupt Operation
Upon acceptance of an interrupt, the following operations are auto-
matically performed.
1.
The processing being executed is stopped.
2.
The contents of the program counter and processor status
register are automatically pushed onto the stack.
3.
Concurrently with the push operation, the interrupt jump
destination address is read from the vector table into the
program counter.
4.
The interrupt disable flag is set and the corresponding interrupt
request bit is cleared.
Notes on use
When the active edge of an external interrupt (INT0, INT1, CNTR0,
CNTR1, CWKU or KOI) is changed, the corresponding interrupt
request bit may also be set. Therefore, take the following sequence.
(1) Disable the external interrupt which is selected.
(2) Change the active edge in interrupt edge selection register.
(in the case of CNTR0: Timer X mode register; in the case of
CNTR1: Timer Y mode register)
(3) Clear the interrupt request bit to “0”.
(4) Enable the external interrupt which is selected.
相關PDF資料 |
PDF描述 |
|---|---|
| M37630E4FP | 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP44 |
| M37640E8FP | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37640E8FS | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37640M8-XXXFP | 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37640E8FP | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37630E4T-XXXFS | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37630M4T | 制造商:CMLMICRO 制造商全稱:CML Microcircuits 功能描述:Baseband Processor for ‘Leisure’ Radios with Data |
| M37630M4T-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37630M4T-XXXFS | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37630T-RFS | 功能描述:BOARD CONV FOR M37630 EMULATOR RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。