- 您現在的位置：買賣IC網 > PDF目錄45035 > M37542M2T-XXXGP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
參數資料
| 型號： | M37542M2T-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件頁數： | 40/139頁 |
| 文件大?。?/td> | 1448K |
| 代理商： | M37542M2T-XXXGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁
7542 Group
Rev.3.02
Oct 31, 2006
Page 134 of 134
REJ03B0006-0302
Notes on On-chip Oscillation Division Ratio
When the clock division ratio is switched from f(XIN) to on-chip
oscillator by the clock division ratio selection bits (bits 7 and 6 of
CPU mode register (address 3B16)), the on-chip oscillator divi-
sion ratio (bits 1 and 0 of on-chip oscillation division ratio
selection register (address 3716)) is “102” (on-chip oscillator
middle-speed mode (ROSC/8)).
Notes on Oscillation Stop Detection Circuit
1. After the reset by the oscillation stop detection, the value of fol-
lowing bits are retained, not initialized.
Ceramic or RC oscillation stop detection function active bit
Bit 1 of MISRG (address 3B16)
Oscillation stop detection status bit
Bit 3 of MISRG
2. Oscillation stop detection status bit is initialized (“0”) by the fol-
lowing operation.
External reset
Write “0” data to the ceramic or RC oscillation stop detection
function active bit.
3. The oscillation stop detection circuit is not included in the emu-
lator MCU “M37542RSS”.
Notes on CPU Rewrite Mode
Take the notes described below when rewriting the flash memory
in CPU rewrite mode.
1. Operation speed
During CPU rewrite mode, set the system clock φ to 4.0 MHz or
less using the clock division ratio selection bits (bits 6 and 7 of
CPU mode register).
2. Instructions inhibited against use
The instructions which refer to the internal data of the flash
memory cannot be used during CPU rewrite mode.
3. Interrupts inhibited against use
The interrupts cannot be used during CPU rewrite mode because
they refer to the internal data of the flash memory.
4. Watchdog timer
If the watchdog timer has been already activated, internal reset
due to an underflow will not occur because the watchdog timer is
surely initialized during program or erase.
5. Reset
Reset is always valid. The MCU is activated using the boot mode
at release of reset in the condition of CNVss = “H”, so that the pro-
gram will begin at the address which is stored in addresses
FFFC16 and FFFD16 of the boot ROM area.
Electric Characteristic Differences Between
Mask ROM, Flash Memory MCUs
There are differences in electric characteristics, operation margin,
noise immunity, and noise radiation among mask ROM and flash
memory version MCUs due to the differences in the manufacturing
processes.
When manufacturing an application system with the flash memory
and then switching to use of the mask ROM version, perform suffi-
cient evaluations for the commercial samples of the mask ROM
version.
Note on Power Source Voltage
When the power source voltage value of a microcomputer is less
than the value which is indicated as the recommended operating
conditions, the microcomputer does not operate normally and may
perform unstable operation.
In a system where the power source voltage drops slowly when
the power source voltage drops or the power supply is turned off,
reset a microcomputer when the supply voltage is less than the
recommended operating conditions and design a system not to
cause errors to the system by this unstable operation.
NOTES ON HARDWARE
Handling of Power Source Pin
In order to avoid a latch-up occurrence, connect a capacitor suit-
able for high frequencies as bypass capacitor between power
source pin (Vcc pin) and GND pin (Vss pin). Besides, connect the
capacitor to as close as possible. For bypass capacitor which
should not be located too far from the pins to be connected, a ce-
ramic capacitor of 0.01 F to 0.1 F is recommended.
相關PDF資料 |
PDF描述 |
|---|---|
| M37542M2T-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| M37542M2T-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37542F8VGP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37542M2V-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37542M2V-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37542M2-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M2-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M2-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M2-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。