- 您現在的位置：買賣IC網 > PDF目錄45035 > M37542M2-XXXGP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
參數資料
| 型號： | M37542M2-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件頁數： | 17/122頁 |
| 文件大?。?/td> | 1311K |
| 代理商： | M37542M2-XXXGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
7542 Group
Rev.3.03
Jul 11, 2008
Page 113 of 117
REJ03B0006-0303
3. Notes common to clock synchronous serial I/O and UART
(1) Set the serial I/Oi (i=1, 2) control register again after the trans-
mission and the reception circuits are reset by clearing both
the transmit enable bit and the receive enable bit to “0.”
Fig. 6 Sequence of setting serial I/Oi control register again
Clear both the transmit enable bit (TE)
and the receive enable bit (RE) to “0”
Set the bits 0 to 3 and bit 6 of the
serial I/Oi control register
Set both the transmit enable bit (TE)
and the receive enable bit (RE), or
one of them to “1”
Notes on Serial I/Oi (i=1, 2)
1. Clock synchronous serial I/O
(1) When the transmit operation is stopped, clear the serial I/Oi
enable bit and the transmit enable bit to “0” (serial I/Oi and
transmit disabled).
<Reason>
Since transmission is not stopped and the transmission circuit is
not initialized even if only the serial I/Oi enable bit is cleared to “0”
(serial I/Oi disabled), the internal transmission is running (in this
case, since pins TxDi, RxDi, SCLKi, and SRDYi function as I/O
ports, the transmission data is not output). When data is written to
the transmit buffer register in this state, data starts to be shifted to
the transmit shift register. When the serial I/Oi enable bit is set to
“1” at this time, the data during internally shifting is output to the
TxDi pin and an operation failure occurs.
(2) When the receive operation is stopped, clear the receive en-
able bit to “0” (receive disabled), or clear the serial I/Oi enable
bit to “0” (serial I/Oi disabled).
(3) When the transmit/receive operation is stopped, clear both the
transmit enable bit and receive enable bit to “0” (transmit and
receive disabled) simultaneously. (any one of data transmis-
sion and reception cannot be stopped.)
<Reason>
In the clock synchronous serial I/O mode, the same clock is used
for transmission and reception.
If any one of transmission and reception is disabled, a bit error oc-
curs because transmission and reception cannot be synchronized.
In this mode, the clock circuit of the transmission circuit also oper-
ates for data reception. Accordingly, the transmission circuit does
not stop by clearing only the transmit enable bit to “0” (transmit
disabled). Also, the transmission circuit cannot be initialized even
if the serial I/Oi enable bit is cleared to “0” (serial I/Oi disabled)
(same as (1)).
(4) When signals are output from the SRDYi pin on the reception
side by using an external clock, set all of the receive enable
bit, the SRDYi output enable bit, and the transmit enable bit to
“1”.
(5) When the SRDYi signal input is used, set the using pin to the in-
put mode before data is written to the transmit/receive buffer
register.
2. UART
When the transmit operation is stopped, clear the transmit enable
bit to “0” (transmit disabled).
<Reason>
Same as (1) shown on the above “1. Clock synchronous serial I/O“.
When the receive operation is stopped, clear the receive enable
bit to “0” (receive disabled).
When the transmit/receive operation is stopped, clear the transmit
enable bit to “0” (transmit disabled) and receive enable bit to “0”
(receive disabled).
(2) The transmit shift completion flag changes from “1” to “0” with
a delay of 0.5 to 1.5 shift clocks. When data transmission is
controlled with referring to the flag after writing the data to the
transmit buffer register, note the delay.
(3) When data transmission is executed at the state that an exter-
nal clock input is selected as the synchronous clock, set “1” to
the transmit enable bit while the SCLKi is “H” state. Also, write
to the transmit buffer register while the SCLKi is “H” state.
(4) When the transmit interrupt is used, set as the following se-
quence.
Serial I/Oi transmit interrupt enable bit is set to “0” (disabled).
Serial I/Oi transmit enable bit is set to “1”.
Serial I/Oi transmit interrupt request bit is set to “0” after 1 or
more instructions have been executed.
Serial I/Oi transmit interrupt enable bit is set to “1” (enabled).
<Reason>
When the transmit enable bit is set to “1”, the transmit buffer
empty flag and transmit shift completion flag are set to “1”.
Accordingly, even if the timing when any of the above flags is set
to “1” is selected for the transmit interrupt source, interrupt request
occurs and the transmit interrupt request bit is set.
(5) Write to the baud rate generator (BRGi) while the transmit/re-
ceive operation is stopped.
Can be set
with the LDM
instruction at
the same time
相關PDF資料 |
PDF描述 |
|---|---|
| M37542F4SP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8HP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQCC36 |
| M37544G2ASP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37544G2ASP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37544G2GP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37542M2-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M2-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M4-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M4-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。