- 您現在的位置：買賣IC網 > PDF目錄45035 > M37540E8T-XXXFP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
7540 Group
Rev.4.00
Jun 21, 2004
page 42 of 82
REJ03B0011-0400Z
Reset Circuit
The microcomputer is put into a reset status by holding the RE-
SET pin at the “L” level for 2
s or more when the power source
voltage is 2.2 to 5.5 V and XIN is in stable oscillation.
After that, this reset status is released by returning the RESET pin
to the “H” level. The program starts from the address having the
contents of address FFFD16 as high-order address and the con-
tents of address FFFC16 as low-order address.
In the case of f(
φ) ≤ 6 MHz, the reset input voltage must be 0.9 V
or less when the power source voltage passes 4.5 V.
In the case of f(
φ) ≤ 4 MHz, the reset input voltage must be 0.8 V
or less when the power source voltage passes 4.0 V.
In the case of f(
φ) ≤ 2 MHz, the reset input voltage must be 0.48 V
or less when the power source voltage passes 2.4 V.
In the case of f(
φ) ≤ 1 MHz, the reset input voltage must be 0.44 V
or less when the power source voltage passes 2.2 V.
Fig. 43 Example of reset circuit
Fig. 44 Timing diagram at reset
(Note)
0.2 VCC
0 V
Poweron
VCC
RESET
VCC
RESET
Power source
voltage
detection circuit
Power source
voltage
Reset input
voltage
Note : Reset release voltage Vcc = 2.2 V
Data
Address
8-13 clock cycles
Reset address from the
vector table
1 : An on-chip oscillator applies about RING2 MHz,
φ250 kHz frequency clock
at average of Vcc = 5 V.
2 : The mark “?” means that the address is changeable depending on the previous state.
3 : These are all internal signals except RESET.
Notes
??
FFFC
FFFD
ADH,ADL
??
?
??
ADL
ADH
??
?
Clock from on-chip
oscillator RING
φ
RESET
RESETOUT
SYNC
相關PDF資料 |
PDF描述 |
|---|---|
| M37540E2FP | 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP32 |
| M37542F8GP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP32 |
| M37542M4-XXXSP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8SP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8VGP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37540E8T-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES |
| M37540E8V-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540E8V-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES |
| M37540EXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540M2T-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。