- 您現在的位置：買賣IC網 > PDF目錄45035 > M37540E2FP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
參數資料
| 型號： | M37540E2FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件頁數： | 17/88頁 |
| 文件大小： | 872K |
| 代理商： | M37540E2FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
7540 Group
Rev.4.00
Jun 21, 2004
page 24 of 82
REJ03B0011-0400Z
(3) Event counter mode
Timer A counts signals input from the P00/CNTR1 pin.
Except for this, the operation in event counter mode is the same
as in timer mode.
The active edge of CNTR1 pin input signal can be selected from
rising or falling by the CNTR1 active edge switch bit .
(4) Pulse width HL continuously measurement mode
In the pulse width HL continuously measurement mode, the pulse
width (“H” and “L” levels) input to the P00/CNTR1 pin is measured.
CNTR1 interrupt request is generated at both rising and falling
edges of CNTR1 pin input signal. Except for this, the operation in
pulse width HL continuously measurement mode is the same as in
period measurement mode.
The count value when trigger input from the CNTR1 pin is ac-
cepted is retained until Timer A is read once.
Timer A can stop counting by setting “1” to the timer A count stop
bit in any mode.
Also, when Timer A underflows, the timer A interrupt request bit is
set to “1”.
Note on Timer A is described below;
s Note on Timer A
CNTR1 interrupt active edge selection
CNTR1 interrupt active edge depends on the CNTR1 active edge
switch bit.
When this bit is “0”, the CNTR1 interrupt request bit is set to “1” at
the falling edge of the CNTR1 pin input signal. When this bit is “1”,
the CNTR1 interrupt request bit is set to “1” at the rising edge of
the CNTR1 pin input signal.
However, in the pulse width HL continuously measurement mode,
CNTR1 interrupt request is generated at both rising and falling
edges of CNTR1 pin input signal regardless of the setting of
CNTR1 active edge switch bit.
Fig. 22 Structure of timer A mode register
Timer A mode register
(TAM : address 001D16, initial value: 0016)
b7
b0
Not used (return “0” when read)
Timer A operating mode bits
b5 b4
0
0 : Timer mode
0
1 : Period measurement mode
1
0 : Event counter mode
1
1 : Pulse width HL continuously
measurement mode
CNTR1 active edge switch bit
0 : Count at rising edge in event counter mode
Measure the falling edge period in period
measurement mode
Falling edge active for CNTR 1 interrupt
1 : Count at falling edge in event counter mode
Measure the rising edge period in period
measurement mode
Rising edge active for CNTR1 interrupt
Timer A count stop bit
0 : Count start
1 : Count stop
qTimer X
Timer X is an 8-bit timer and counts the prescaler X output.
When Timer X underflows, the timer X interrupt request bit is set
to “1”.
Prescaler X is an 8-bit prescaler and counts the signal selected by
the timer X count source selection bit.
Prescaler X and Timer X have the prescaler X latch and the timer
X latch to retain the reload value, respectively. The value of
prescaler X latch is set to Prescaler X when Prescaler X
underflows.The value of timer X latch is set to Timer X when Timer
X underflows.
When writing to Prescaler X (PREX) is executed, the value is writ-
ten to both the prescaler X latch and Prescaler X.
When writing to Timer X (TX) is executed, the value is written to
both the timer X latch and Timer X.
When reading from Prescaler X (PREX) and Timer X (TX) is ex-
ecuted, each count value is read out.
Timer X can can be selected in one of 4 operating modes by set-
ting the timer X operating mode bits of the timer X mode register.
(1) Timer mode
Prescaler X counts the count source selected by the timer X count
source selection bits. Each time the count clock is input, the con-
tents of Prescaler X is decremented by 1. When the contents of
Prescaler X reach “0016”, an underflow occurs at the next count
clock, and the prescaler X latch is reloaded into Prescaler X and
count continues. The division ratio of Prescaler X is 1/(n+1) pro-
vided that the value of Prescaler X is n.
The contents of Timer X is decremented by 1 each time the under-
flow signal of Prescaler X is input. When the contents of Timer X
reach “0016”, an underflow occurs at the next count clock, and the
timer X latch is reloaded into Timer X and count continues. The di-
vision ratio of Timer X is 1/(m+1) provided that the value of Timer
X is m. Accordingly, the division ratio of Prescaler X and Timer X is
1/((n+1)(m+1)) provided that the value of Prescaler X is n and
the value of Timer X is m.
(2) Pulse output mode
In the pulse output mode, the waveform whose polarity is inverted
each time timer X underflows is output from the CNTR0 pin.
The output level of CNTR0 pin can be selected by the CNTR0 ac-
tive edge switch bit. When the CNTR0 active edge switch bit is “0”,
the output of CNTR0 pin is started at “H” level. When this bit is “1”,
the output is started at “L” level.
Also, the inverted waveform of pulse output from CNTR0 pin can
be output from TXOUT pin by setting “1” to the P03/TXOUT output
valid bit.
When using a timer in this mode, set the port P14 and P03 direc-
tion registers to output mode.
(3) Event counter mode
The timer A counts signals input from the P14/CNTR0 pin.
Except for this, the operation in event counter mode is the same
as in timer mode.
The active edge of CNTR0 pin input signal can be selected from
rising or falling by the CNTR0 active edge switch bit .
相關PDF資料 |
PDF描述 |
|---|---|
| M37542F8GP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP32 |
| M37542M4-XXXSP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8SP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8VGP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP32 |
| M37542F8FP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37540E2GP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES |
| M37540E2SP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540E8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540E8FP#U0 | 功能描述:MCU 2/5V 32K PB-FREE 36-SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M37540E8FP(#UO) | 制造商:Renesas Electronics Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。