- 您現在的位置：買賣IC網 > PDF目錄45034 > M37532E8FP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36 PDF資料下載
參數資料
| 型號： | M37532E8FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36 |
| 封裝： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-36 |
| 文件頁數： | 4/51頁 |
| 文件大?。?/td> | 736K |
| 代理商： | M37532E8FP |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7532 Group
MITSUBISHI MICROCOMPUTERS
11
I/O Ports
[Direction registers] PiD
The I/O ports have direction registers which determine the input/out-
put direction of each pin. Each bit in a direction register corresponds
to one pin, and each pin can be set to be input or output.
When “1” is set to the bit corresponding to a pin, this pin becomes an
output port. When “0” is set to the bit, the pin becomes an input port.
When data is read from a pin set to output, not the value of the pin
itself but the value of port latch is read. Pins set to input are floating,
and permit reading pin values.
If a pin set to input is written to, only the port latch is written to and the
pin remains floating.
[Pull-up control] PULL
By setting the pull-up control register (address 001616), ports P0 and
P3 can exert pull-up control by program. However, pins set to output
are disconnected from this control and cannot exert pull-up control.
[Port P1P3 control] P1P3C
By setting the port P1P3 control register (address 001716), a CMOS
input level or a TTL input level can be selected for ports P10, P12,
P13, and P37 by program.
Then, set “1” to each bit 6 of the port P3 direction register and port P3
register.
Fig. 12 Structure of port P1P3 control register
Fig. 11 Structure of pull-up control register
Pull-up control register
(PULL: address 0016 16)
P00 pull-up control bit
P01 pull-up control bit
P02, P03 pull-up control bit
P04 – P07 pull-up control bit
P30 – P33 pull-up control bit
P34 pull-up control bit
P35 pull-up control bit
P37 pull-up control bit
Note : Pins set to output ports are disconnected from pull-up control.
b7
b0
0: Pull-up off
1: Pull-up on
Initial value: FF16
Port P1P3 control register
(P1P3C: address 0017 16)
b7
b0
P37/INT0 input level selection bit
0 : CMOS level
1 : TTL level
Not used
(Do not write “1” to this bit)
P10,P12,P13 input level selection bit
0 : CMOS level
1 : TTL level
Not used
相關PDF資料 |
PDF描述 |
|---|---|
| M37532M4-XXXGP | 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32 |
| M37536M4-XXXSP | 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PDIP42 |
| M37536E8SP | 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDIP42 |
| M37540E8FP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO36 |
| M37540M4T-XXXGP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37532M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37532M4-A17GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37532M4-XXXFP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| M37532M4-XXXGP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| M37532RSS | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發(fā)布緊急采購，3分鐘左右您將得到回復。