- 您現在的位置：買賣IC網 > PDF目錄370845 > M37516RSS (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37516RSS |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 34/54頁 |
| 文件大小： | 358K |
| 代理商： | M37516RSS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
34/54
M37516M6-XXXHP
GNOK-M37516M6-XXXHP-50
(MSETSU 2)
PA
GE
(2) START condition generating procedure using multi-master
1. Procedure example (The necessary conditions of the generat-
ing procedure are described as the following 2 to 5.
:
LDA —
(Taking out of slave address value)
SEI
(Interrupt disabled)
BBS 5, S1, BUSBUSY (BB flag confirming and branch process)
BUSFREE:
STA S0
(Writing of slave address value)
LDM #$F0, S1
(Trigger of START condition generating)
CLI
(Interrupt enabled)
:
BUSBUSY:
CLI
(Interrupt enabled)
:
2. Use “Branch on Bit Set” of “BBS 5, $002D, –” for the BB flag
confirming and branch process.
3. Use “STA $2B, STX $2B” or “STY $2B” of the zero page ad-
dressing instruction for writing the slave address value to the
I
2
C data shift register.
4. Execute the branch instruction of above 2 and the store instruc-
tion of above 3 continuously shown the above procedure
example.
5. Disable interrupts during the following three process steps:
BB flag confirming
Writing of slave address value
Trigger of START condition generating
When the condition of the BB flag is bus busy, enable interrupts
immediately.
(3) RESTART condition generating procedure
1. Procedure example (The necessary conditions of the generat-
ing procedure are described as the following 2 to 4.)
Execute the following procedure when the PIN bit is “0.”
:
LDM #$00, S1
(Select slave receive mode)
LDA —
(Taking out of slave address value)
SEI
(Interrupt disabled)
STA S0
(Writing of slave address value)
LDM #$F0, S1
(
Trigger of RESTART condition generating
)
CLI
(Interrupt enabled)
:
2. Select the slave receive mode when the PIN bit is “0.” Do not
write “1” to the PIN bit. Neither “0” nor “1” is specified for the
writing to the BB bit.
The TRX bit becomes “0” and the SDA pin is released.
3. The SCL pin is released by writing the slave address value to
the I
2
C data shift register.
4. Disable interrupts during the following two process steps:
Writing of slave address value
Trigger of RESTART condition generating
(4) Writing to I
2
C status register
Do not execute an instruction to set the PIN bit to “1” from “0” and
an instruction to set the MST and TRX bits to “0” from “1” simulta-
neously. It is because it may enter the state that the SCL pin is
released and the SDA pin is released after about one machine
cycle. Do not execute an instruction to set the MST and TRX bits
to “0” from “1” simultaneously when the PIN bit is “1.” It is because
it may become the same as above.
(5) Process of after STOP condition generating
Do not write data in the I
2
C data shift register S0 and the I
2
tus register S1 until the bus busy flag BB becomes “0” after
generating the STOP condition in the master mode. It is because
the STOP condition waveform might not be normally generated.
Reading to the above registers do not have the problem.
I
Precautions when using multi-master I
2
C-BUS
interface
(1) Read-modify-write instruction
The precautions when the read-modify-write instruction such as
SEB, CLB etc. is executed for each register of the multi-master
I
2
C-BUS interface are described below.
I
2
C data shift register (S0: address 002B
16
)
When executing the read-modify-write instruction for this regis-
ter during transfer, data may become a value not intended.
I
2
C address register (S0D: address 002C
16
)
When the read-modify-write instruction is executed for this regis-
ter at detecting the STOP condition, data may become a value
not intended. It is because H/W changes the read/write bit
(RWB) at the above timing.
I
2
C status register (S1: address 002D
16
)
Do not execute the read-modify-write instruction for this register
because all bits of this register are changed by H/W.
I
2
C control register (S1D: address 002E
16
)
When the read-modify-write instruction is executed for this regis-
ter at detecting the START condition or at completing the byte
transfer, data may become a value not intended. Because H/W
changes the bit counter (BC0-BC2) at the above timing.
I
2
C clock control register (S2: address 002F
16
)
The read-modify-write instruction can be executed for this regis-
ter.
I
2
C START/STOP condition control register (S2D: address
0030
16
)
The read-modify-write instruction can be executed for this regis-
ter.
相關PDF資料 |
PDF描述 |
|---|---|
| M37516M6-A05 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516M6-A05HP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516M6-A06HP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516M6-A14HP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E8FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37517F8HP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37530T-PTC | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting 42-pin 1.778mm-pitch SDIP to a 40-pin Narrow-pitch Connector (for 7531, 7540, 7542 and 7544 Groups) |
| M37530T-PTCB | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting 40-pin Narrow-pitch Connector to 32-pin 0.8mm-pitch LQFP (for 7531, 7532, 7534, 7540, 7542 and 7544 Groups) |
| M37530T-PTCC | 功能描述:DEV 42-PIN RSS/MCU TO 32-PIN 1.7 RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M37531E4FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。