- 您現在的位置：買賣IC網 > PDF目錄45033 > M37513M8-XXXGP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M37513M8-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件頁數： | 39/68頁 |
| 文件大?。?/td> | 1010K |
| 代理商： | M37513M8-XXXGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
41
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
7513 Group
Common Pin and Duty Ratio Control
The common pins (COM0–COM3) to be used are determined by
duty ratio.
Select duty ratio by the duty ratio selection bits (bits 0 and 1 of the
LCD mode register).
When releasing from reset, the VCC (VL3) voltage is output from
the common pins.
Table 11 Duty ratio control and common pins used
Duty
ratio
Common pins used
Notes1: COM2 and COM3 are open.
2: COM3 is open.
Bit 1
Bit 0
COM0, COM1 (Note 1)
Duty ratio selection bit
2
3
4
0
1
0
1
COM0–COM2 (Note 2)
COM0–COM3
Segment Signal Output Pin
Segment signal output pins are classified into the segment-only
pins (SEG0–SEG17), the segment/output port pins (SEG18–
SEG25), and the segment/I/O port pins (SEG26–SEG39).
Segment signals are output according to the bit data of the LCD
RAM corresponding to the duty ratio. After reset release, a VCC
(=VL3) voltage is output to the segment-only pins and the seg-
ment/output port pins are the high impedance condition. The seg-
ment/I/O port pins(SEG26–SEG33). are set to input ports, and the
high impedance condition.The segment/I/O port pins(SEG34–
SEG39). are set to input ports, and VCC (=VL3) is applied to them
by pull-up resistor.
LCD Display RAM
Address 004016 to 005316 is the designated RAM for the LCD dis-
play. When “1” are written to these addresses, the corresponding
segments of the LCD display panel are turned on.
LCD Drive Timing
The LCDCK timing frequency (LCD drive timing) is generated in-
ternally and the frame frequency can be determined with the
following equation;
f(LCDCK) =
Frame frequency =
Fig. 43 LCD display RAM map
(frequency of count source for LCDCK)
(divider division ratio for LCD)
f(LCDCK)
(duty ratio)
Bit
address
76
5
432
1
0
004016
004116
004216
004316
004416
004516
004616
SEG1
SEG3
SEG5
SEG7
SEG9
SEG0
SEG2
SEG4
SEG6
SEG8
SEG10
COM3 COM2 COM1 COM0
SEG12
SEG14
SEG16
SEG18
SEG20
SEG22
SEG24
SEG26
SEG28
SEG30
SEG32
SEG34
SEG36
SEG38
SEG21
SEG23
SEG25
SEG27
SEG11
SEG13
SEG15
SEG17
SEG19
SEG29
SEG31
SEG33
SEG35
SEG37
SEG39
004716
004816
004916
004A16
004B16
004C16
004D16
004E16
004F16
005016
005116
005216
005316
COM3 COM2 COM1 COM0
相關PDF資料 |
PDF描述 |
|---|---|
| M37513EFGP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP100 |
| M37516E6HP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP48 |
| M37516M8-XXXHP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP48 |
| M37516M4H-XXXKP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP44 |
| M37516M6H-XXXKP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37513M8-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37513M9-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37513MA-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37513MB-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37513MC-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。