- 您現在的位置：買賣IC網 > PDF目錄370845 > M37510M6156FP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37510M6156FP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 16/43頁 |
| 文件大?。?/td> | 614K |
| 代理商： | M37510M6156FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
16
7510 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Timer Y
Timer Y is a 16-bit timer that can be selected in one of four modes.
Timer mode
The timer counts f(X
IN
)/16 (or f(X
CIN
)/16, if the selected system
clock
φ
is f(X
CIN
)/2).
Period measurement mode
CNTR
1
interrupt request is generated at rising/falling edge of
CNTR
1
pin input signal. Simultaneously, the value in timer Y latch
is reloaded in timer Y and timer Y continues counting down. Except
for the above-mentioned, the operation in period measurement
mode is the same as in timer mode.
The timer value just before the reloading at rising/falling of CNTR
1
pin input signal is retained until the timer Y is read once after the
reload.
The rising/falling timing of CNTR
1
pin input signal is found by
CNTR
1
interrupt.
Event counter mode
The timer counts signals input through the CNTR
1
pin. Except for
this, the operation in event counter mode is the same as in timer
mode.
Pulse width HL continuously measurement mode
CNTR
1
interrupt request is generated at both rising and falling
edges of CNTR
1
pin input signal. Except for this, the operation in
pulse width HL continuously measurement mode is the same as in
period measurement mode.
Note on CNTR
1
Interrupt Active Edge
Selection
CNTR
1
interrupt active edge depends on the CNTR
1
active edge
selection bit. However, in pulse width HL continuously measure-
ment mode, CNTR
1
interrupt request is generated at both rising
and falling edges of CNTR
1
pin input signal regardless of the set-
ting of CNTR
1
active edge selection bit.
Fig. 11 Structure of timer Y mode register
Not used (return “0” when read)
Timer Y operation mode bits
b5 b4
0 0 : Timer mode
0 1 : Period measurement mode
1 0 : Event counter mode
1 1 : Pulse width HL continuously
measurement mode
CNTR
1
active edge selection bit
0 : Count at rising edge in event counter mode
Measure the falling edge to falling edge
period in period measurement mode
Falling edge active for CNTR
1
interrupt
1 : Count at falling edge in event counter mode
Measure the rising edge to rising edge
period in period measurement mode
Rising edge active for CNTR
1
interrupt
Timer Y stop control bit
0 : Count start
1 : Count stop
b7
Timer Y mode register
(TYM : address 0028
16
)
b0
相關PDF資料 |
PDF描述 |
|---|---|
| M37510M7156FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37510M8156FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37510 | Single Chip 8 Bits CMOS Microcomputer(8位單片機) |
| M37510M6156FPEF | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37515M4-C05HP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37510M6156FPEF | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37510M7156FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37510M8156FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37512F8HHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37512F8HP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。