參數資料
型號： M37510M4156FP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 15/43頁
文件大?。?/td> 614K
代理商： M37510M4156FP
15
7510 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
responding to that timer is set to “1”.
Read and write operation on 16-bit timer must be performed for
both high and low-order bytes. When reading a 16-bit timer, read
the high-order byte first. When writing to a 16-bit timer, write the
low-order byte first. The 16-bit timer cannot perform the correct op-
eration when reading during the write operation, or when writing
during the read operation.
Timer X
Timer X is a 16-bit timer that can be selected in one of four modes
and can be controlled the timer X write by setting the timer X
mode register.
Timer mode
The timer counts f(X
IN
)/16 (or f(X
CIN
)/16, if the selected system
clock
φ
is f(X
CIN
)/2).
Pulse output mode
Each time the timer underflows, a signal output from the CNTR
0
pin is inverted. Except for this, the operation in pulse output mode
is the same as in timer mode. When using a timer in this mode, set
the corresponding port P4
2
direction register to output mode.
Event counter mode
The timer counts signals input through the CNTR
0
pin. Except for
this, the operation in event counter mode is the same as in timer
mode.
Pulse width measurement mode
The count source is f(X
IN
)/16 (or f(X
CIN
)/16, if the selected system
clock
φ
is f(X
CIN
)/2). If CNTR
0
active edge selection bit is “0”, the
timer counts while the input signal of CNTR
0
pin is at “H”. If it is
“1”, the timer counts while the input signal of CNTR
0
pin is at “L”.
Timer X Write Control
If the timer X write control bit is “0”, when the value is written in the
address of timer X, the value is loaded in the timer X and the latch
at the same time.
If the timer X write control bit is “1”, when the value is written in the
address of timer X, the value is loaded only in the latch. The value
in the latch is loaded in timer X after timer X underflows.
If the value is written in latch only, unexpected value may be set in
the high-order counter when the writing in high-order latch and the
underflow of timer X are performed at the same timing.
Note on CNTR
0
Interrupt Active Edge
Selection
CNTR
0
interrupt active edge depends on the CNTR
0
active edge
selection bit.
Fig. 10 Structure of timer X mode register
Timer X write control bit
0 : Write data in latch and timer
1 : Write data in latch only
Not used (Always write “0” )
Timer X operation mode bits
b5 b4
0 0 : Timer mode
0 1 : Pulse output mode
1 0 : Event counter mode
1 1 : Pulse width measurement mode
CNTR
0
active edge selection bit
0 : Count at rising edge in event counter mode
Start from “H” output in pulse output mode
Measure “H” pulse width in pulse width
measurement mode
Falling edge active for CNTR
0
interrupt
1 : Count at falling edge in event counter mode
Start from “L” output in pulse output mode
Measure “L” pulse width in pulse width
measurement mode
Rising edge active for CNTR
0
interrupt
Timer X stop control bit
0 : Count start
1 : Count stop
b7
Timer X mode register
(TXM : address 0027
16
)
b0
相關PDF資料
PDF描述
M37510M5156FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M6 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M6156FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M7156FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M8156FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M37510M5156FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M6 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M6156FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M6156FPEF 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M7156FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*