- 您現在的位置：買賣IC網 > PDF目錄45032 > M37471E8SS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CDIP42 PDF資料下載
參數資料
| 型號： | M37471E8SS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CDIP42 |
| 封裝： | 0.600 INCH, 1.78 MM PITCH, PLASTIC, SDIP-42 |
| 文件頁數： | 15/49頁 |
| 文件大?。?/td> | 601K |
| 代理商： | M37471E8SS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
19
7470/7471 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Fig. 10 Structure of serial I/O mode register
BYTE SPECIFY MODE
The serial I/O has a byte specify mode that allows one specific
byte data to be selected for transmission or reception when serial
I/O circuits of two or more microcomputers are connected to send
or receive data through one bus. The data to be sent or received
can be specified by writing a value into the byte counter. The value
written in the byte counter is decremented by one each time eight
cycles of transfer clock are input. When the value in the byte
counter becomes “0”, serial transmission/reception is done by the
next eight cycles of transfer clock. When the value in the byte
counter is not “0”, the output on the SOUT pin is driven “H” by the
falling edge of the first transfer clock pulse to inhibit transmission/
reception.
Serial I/O interrupt requests are generated only when serial trans-
mission/reception is done after the value in the byte counter is
decremented to “0”. When the SARDY signal output is selected, the
SARDY signal is driven “L” by the last rising edge of the transfer
clock after the value in the byte counter is decremented to “0”.
Note that in the byte mode, an external clock must be used as the
sync. clock for the purpose of the mode.
b7
b0
Serial I/O mode register (SM)
(Address 00DC16)
Synchronous clock selection bit
0 : External clock
1 : Internal clock
Internal clock selection bits
00 : f(XIN) or f(XcIN) divided by 8
01 : f(XIN) or f(XcIN) divided by 16
10 : f(XIN) or f(XcIN) divided by 32
11 : f(XIN) or f(XcIN) divided by 512
Serial I/O port selection bit
0 : Normal I/O port
1 : SOUT, CLK pins
Note : Do not select f(XCIN) as the count source in the 7470 group.
Serial I/O byte specify mode selection bit
0 : Normal mode
1 : Byte specify mode
SRDY signal output selection bit
0 : Normal I/O port
1 : SRDY signal output pin
SRDY signal selection bit
0 : SRDY signal
1 : SARDY signal
P15/SOUT, P17/SRDY output structure selection bit
0 : CMOS output
1 : N-channel open drain output
相關PDF資料 |
PDF描述 |
|---|---|
| M37471RSS | 8-BIT, 8 MHz, MICROCONTROLLER, CDIP42 |
| M37478RSS | 8-BIT, 8 MHz, MICROCONTROLLER, CDIP42 |
| M37477E8TXXXSP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37477E8TXXXFP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO32 |
| M37477E8FP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37471E8-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37471E8-XXXSP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37471M2 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37471M2-165FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37471M2-495SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。