- 您現在的位置：買賣IC網 > PDF目錄370841 > M37270MF-168SP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER PDF資料下載
參數資料
| 型號： | M37270MF-168SP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| 中文描述： | 單芯片8位CMOS微機隱蔽字幕解碼器和屏幕顯示控制器 |
| 文件頁數： | 28/94頁 |
| 文件大小： | 1551K |
| 代理商： | M37270MF-168SP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
MITSUBISHI MICROCOMPUTERS
M37270MF-XXXSP
M37270EF-XXXSP, M37270EFSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
28
(1) Clamping Circuit and Low-pass Filter
This filter attenuates the noise of the composite video signal input
from the CV
IN
pin. The CV
IN
pin to which composite video signal is
input requires a capacitor (0.1
μ
F) coupling outside. Pull down the
CV
IN
pin with a resistor of hundreds of kiloohms to 1 M . In addition,
we recommend to install externally a simple low-pass filter using a
resistor and a capacitor at the CV
IN
pin (refer to Figure 19).
(2) Sync Slice Circuit
This circuit takes out a composite sync signal from the output signal
of the low-pass filter. Figure 21 shows the structure of the sync slice
register.
(3) Synchronizing Signal Separation Circuit
This circuit separates a horizontal synchronizing signal and a vertical
synchronizing signal from the composite sync signal taken out in the
sync slice circuit.
Horizontal synchronizing signal (H
sep
)
A one-shot horizontal synchronizing signal Hsep is generated at
the falling edge of the composite sync signal.
Vertical synchronizing signal (V
sep
)
As a V
sep
signal generating method, it is possible to select one of
the following 2 methods by using bit 7 of the sync slice register
(address 00E3
16
).
Method 1
The “L” level width of the composite sync signal is
measured. If this width exceeds a certain time, a V
sep
signal is generated in synchronization with the rising
of the timing signal immediately after this “L” level.
Method 2
The “L” level width of the composite sync signal is
measured. If this width exceeds a certain time, it is
detected whether a falling of the composite sync
signal exits or not in the “L” level period of the timing
signal immediately after this “L” level. If a falling exists,
a V
sep
signal is generated in synchronization with
the rising of the timing signal (refer to Figure 22).
Figure 22 shows a V
sep
generating timing. The timing signal shown
in the figure is generated from the reference clock which the timing
generating circuit outputs.
Reading bit 5 of data slicer control register 2 permits determinating
the shape of the V-pulse portion of the composite sync signal. As
shown in Figure 23, when the A level matches the B level, this bit is
“0.” In the case of a mismatch, the bit is “1.”
For the pins RVCO and the HLF, connect a resistor and a capacitor
as shown in Figure 19. Make the length of wiring which is connected
to these pins as short as possible so that a leakage current may not
be generated.
Note:
It takes a few tens of milliseconds until the reference clock
becomes stable after the data slicer and the timing signal
generating circuit are started. In this period, various timing
signals, H
sep
signals and V
sep
signals become unstable. For
this reason, take stabilization time into consideration when
programming.
Fig. 21. Structure of sync slice register
Fig. 22. Vsep generating timing (method 2)
Composite
sync signal
Timing
signal
V
sep
signal
Measure “L” period
A V
sep
signal is generated at a rising of the timing signal
immediately after the “L” level width of the composite
sync signal exceeds a certain time.
0
0
0
0
7
Sync slice register
(SSL : address 00E3
16
)
Fix these bits to “0000101
2
”
Vertical synchronizing
signal (V
sep
) generating
method selection bit
0 : Method 1
1 : Method 2
0
0
1
1
相關PDF資料 |
PDF描述 |
|---|---|
| M37271EF-XXXSP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271MF-XXXSP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271MF-220SP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271MF-231SP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271MF-252SP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37270MF-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271EF | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271EFSP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271EFSS | 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M37271EF-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。