參數(shù)資料
型號: M37220M3-160SP
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
中文描述: 單芯片8位CMOS微機電壓合成與屏幕顯示控制器
文件頁數(shù): 17/53頁
文件大?。?/td> 1281K
代理商: M37220M3-160SP
MITSUBISHI MICROCOMPUTERS
M37220M3-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
17
7
Serial I/O mode register
(SM : address 00DC
16
)
Internal synchronizing clock
selection bits
b1 b0
0 0 : f(X
IN
)/4
0 1 : f(X
IN
)/16
1 0 : f(X
IN
)/32
1 1 : f(X
IN
)/64
0
0
Synchronizing clock selection bit
0 : External clock
1 : Internal clock
Serial I/O port selection bit
0 : P2
0
, P2
1
functions as port
1 : S
CLK
, S
OUT
Fix this bit to “0.”
Transfer direction selection bit
0 : LSB first
1 : MSB first
Serial input pin selection bit
0 : Input signal from S
IN
pin
1 : Input signal from S
OUT
pin
Internal clock—the serial I/O counter is set to “7” during write cycle
into the serial I/O register (address 00DD
16
), and transfer clock goes
“H” forcibly. At each falling edge of the transfer clock after the write
cycle, serial data is output from the S
OUT
pin. Transfer direction can
be selected by bit 5 of the serial I/O mode register. At each rising
edge of the transfer clock, data is input from the S
IN
pin and data in
the serial I/O register is shifted 1 bit.
After the transfer clock has counted 8 times, the serial I/O counter
becomes “0” and the transfer clock stops at “H.” At this time the inter-
rupt request bit is set to “1.”
External clock—when an external clock is selected as the clock
source, the interrupt request is set to “1” after the transfer clock has
counted 8 times. However, transfer operation does not stop, so con-
trol the clock externally. Use the external clock of 1MHz or less with
a duty cycle of 50%.
The serial I/O timing is shown in Figure 11. When using an external
clock for transfer, the external clock must be held at “H” for initializing
the serial I/O counter. When switching between an internal clock and
an external clock, do not switch during transfer. Also, be sure to ini-
tialize the serial I/O counter after switching.
Notes 1:
On programming, note that the serial I/O counter is set by
writing to the serial I/O register with the bit managing in-
structions as SEB and CLB instructions.
2:
When an external clock is used as the synchronizing clock,
write transmit data to the serial I/O register at “H” of the
transfer clock input level.
Fig. 10. Structure of serial I/O mode register
Fig. 11. Serial I/O timing (for LSB first)
Synchroninzing clock
Transfer clock
Serial I/O register
write signal
Serial I/O output
S
OUT
D
0
D
1
D
2
D
3
D
4
D
5
D
6
D
7
(Note)
Serial I/O input
S
IN
Note :
When an internal clock is selected, the S
OUT
pin is at high-impedance after transfer is completed.
Interrupt request bit is set to “1”
相關PDF資料
PDF描述
M37220M3-167SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37273EF8SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37273E8SP Single Chip 8 Bits Microcomputer(8位單片機)
M37273EFSP Single Chip 8 Bits Microcomputer(8位單片機)
M37273M8 Single Chip 8 Bits Microcomputer(8位單片機)
相關代理商/技術參數(shù)
參數(shù)描述
M37220M3-167SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37220M3-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37221 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
M37221EAFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37221EASP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER