參數(shù)資料
型號: M37210M3-XXXFP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PQFP64
封裝: 14 X 14 MM, 0.80 MM PITCH, PLASTIC, QFP-64
文件頁數(shù): 39/60頁
文件大小: 1009K
代理商: M37210M3-XXXFP
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP
M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
43
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM production.
(1) Mask ROM Order Confirmation Form
(2) Mark Specification Form
(3) Data to be written to ROM, in EPROM form (28-pin DIP type
27256, three identical copies)
PROM Programming Method
The built-in PROM of the blank One Time PROM version and built-in
EPROM version can be read or programmed with a general-purpose
PROM programmer using a special programming adapter.
Product
M37210E4SP
M37210E4FP
Name of Programming Adapter
PCA4754
PCA4756
The PROM of the blank One Time PROM version is not tested
or screened in the assembly process and following processes. To
ensure proper operation after programming, the procedure shown
in Figure 45 is recommended to verify programming.
Fig. 45 Programming and testing of One Time PROM version
Programming with
PROM programmer
Screening (Caution)
(150 for 40 hours)
Verification with
PROM programmer
Functional check in target device
Caution : The screening temperature is far higher than the
storage temperature. Never expose to 150°C ex-
ceeding 100 hours.
PROGRAMMING NOTES
(1) The divide ratio of the timer is 1/ (n + 1).
(2) Even though the BBC and BBS instructions are executed imme-
diately after the interrupt request bits are modified (by the pro-
gram), those instructions are only valid for the contents before
the modification. At least one instruction cycle is needed (such as
an NOP) between the modification of the interrupt request bits
and the execution of the BBC and BBS instructions.
(3) After the ADC and SBC instructions are executed (indecimal op-
eration mode), one instruction cycle (such as an NOP) is needed
before the SEC, CLC, or CLD instructions are executed.
(4) An NOP instruction is needed immediately after the execution of
a PLP instruction.
(5) In order to avoid noise and latch-up, connect a bypass capacitor
(
≈ 0.1F) directly between the VCC pin and VSS pin using a thick
wire.
相關PDF資料
PDF描述
M37211M2-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP52
M37210E4-XXXSP 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDIP52
M37212EFFP 8-BIT, OTPROM, MICROCONTROLLER, PQFP80
M37212M4-XXXSP 8-BIT, MROM, MICROCONTROLLER, PDIP52
M37212EFSP 8-BIT, OTPROM, MICROCONTROLLER, PDIP52
相關代理商/技術參數(shù)
參數(shù)描述
M37210M3-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M4-218SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M4-227SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M4-562SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER