參數資料
型號： M37210M3-010SP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
中文描述： 單芯片8位CMOS微機電壓合成與屏幕顯示控制器
文件頁數： 14/59頁
文件大?。?/td> 764K
代理商： M37210M3-010SP
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP
M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
14
Fig. 9 Serial I/O timing (for LSB first)
The serial I/O counter is set to 7 when data is stored in the serial I/O
register. At each falling edge of the transfer clock, serial data is out-
put to S
OUT
. During the rising edge of this clock, data can be input
from S
IN
and the data in the serial I/O register will be shifted 1 bit.
Transfer direction can be selected by bit 5 of serial I/O mode register.
After the transfer clock has counted 8 times, the serial I/O register will
be empty and the transfer clock will remain at a high level. At this time
the interrupt request bit will be set.
External clock- If an external clock is used, the interrupt request will
be sent after the transfer clock has counted 8 times but transfer clock
will not stop.
Due to this reason, the external clock must be controlled from the
outside. The external clock should not exceed 1MHz at a duty cycle
of 50%. The timing diagram is shown in Figure 9. When using an ex-
ternal clock for transfer, the external clock must be held at “H” level
when the serial I/O counter is initialized. When switching between the
internal clock and external clock, the switching must not be per-
formed during transfer. Also, the serial I/O counter must be initialized
after switching.
Notes 1:
On programming, note that the serial I/O counter is set by
writing to the serial I/O register with the bit managing in-
structions as SEB and CLB instructions.
2:
When an external clock is used as the synchronizing clock,
write transmit data to the serial I/O register at “H” of the
transfer clock input level.
D
0
D
1
D
2
D
3
D
4
D
5
D
6
D
7
(Note 1)
Interrupt request bit set
Sync. clock
Transfer clock
Serial I/O register
write signal
Serial I/O output
S
OUT
Serial I/O input
S
IN
Notes 1 : If internal clock is selected, the Sout pin is at high impedance after transfer is completed.
2 : When an external clock is used as the synchronous clock, write the transmit data to the
serial I/O shift register at “H” of the transfer clock input level.
相關PDF資料
PDF描述
M37210M4-218SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M4-227SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M4-562SP RESIS,4.7K,5%,1-8W,SMT1206
M37210M4-657SP RES 4.7K-OHM 5% 0.125W 200PPM THK-FILM SMD-1206 BULK
M37210M4-787SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
相關代理商/技術參數
參數描述
M37210M3-506SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M3-509SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M3-560SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M3-562SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M3-589SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*