- 您現在的位置：買賣IC網 > PDF目錄45029 > M37150MF-XXXFP 8-BIT, MROM, 8.95 MHz, MICROCONTROLLER, PDSO42 PDF資料下載
參數資料
| 型號： | M37150MF-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8.95 MHz, MICROCONTROLLER, PDSO42 |
| 封裝： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件頁數： | 79/142頁 |
| 文件大小： | 1712K |
| 代理商： | M37150MF-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁當前第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
M37150M6/M8/MA/MC/MF-XXXFP, M37150EFFP
MITSUBISHI MICROCOMPUTERS
40
Rev. 1.0
8.6.10 Example of Master Transmission
An example of master transmission in the standard clock mode, at
the SCL frequency of 100 kHz with the ACK return mode enabled, is
shown below.
Set a slave address in the high-order 7 bits of the I2C address
register (address 00F716) and “0” in the RBW bit.
Set the ACK return mode and SCL = 100 kHz by setting “8516” in
the I2C clock control register (address 00FA16).
Set “1016” in the I2C status register (address 00F816) and hold the
SCL at HIGH.
Set a communication enable status by setting “4816” in the I2C
control register (address 00F916).
Set the address data of the destination of transmission in the high-
order 7 bits of the I2C data shift register (address 00F616) and set
“0” in the least significant bit.
Set “F016” in the I2C status register (address 00F816) to generate
a START condition. At this time, an SCL for 1 byte and an ACK
clock automatically occurs.
Set transmit data in the I2C data shift register (address 00F616). At
this time, an SCL and an ACK clock automatically occurs.
When transmitting control data of more than 1 byte, repeat step .
Set “D016” in the I2C status register (address 00F816). After this, if
ACK is not returned or transmission ends, a STOP condition will
be generated.
8.6.11 Example of Slave Reception
An example of slave reception in the high-speed clock mode, at the
SCL frequency of 400 kHz, with the ACK non-return mode enabled
while using the addressing format, is shown below.
Set a slave address in the high-order 7 bits of the I2C address
register (address 00F716) and “0” in the RBW bit.
Set the ACK non-return mode and SCL = 400 kHz by setting “2516”
in the I2C clock control register (address 00FA16).
Set “1016” in the I2C status register (address 00F816) and hold the
SCL at HIGH.
Set a communication enable status by setting “4816” in the I2C
control register (address 00F916).
When a START condition is received, an address comparison is
executed.
When all transmitted address are“0” (general call):
AD0 of the I2C status register (address 00F816) is set to “1” and
an interrupt request signal occurs.
When the transmitted addresses match the address set in :
ASS of the I2C status register (address 00F816) is set to “1” and
an interrupt request signal occurs.
In the cases other than the above:
AD0 and AAS of the I2C status register (address 00F816) are set
to “0” and no interrupt request signal occurs.
Set dummy data in the I2C data shift register (address 00F616).
When receiving control data of more than 1 byte, repeat step .
When a STOP condition is detected, the communication ends.
相關PDF資料 |
PDF描述 |
|---|---|
| M37150MC-XXXFP | 8-BIT, MROM, 8.95 MHz, MICROCONTROLLER, PDSO42 |
| M37151MC-XXXFP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDSO42 |
| M37151MF-XXXFP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDSO42 |
| M37151M6-XXXFP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDSO42 |
| M37151M8-XXXFP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDSO42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37151 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37151EFFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37151EFSS | 功能描述:DEV MCU/8BIT CMOS EMULATION CHIP RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| M37151ERSS | 制造商:Renesas Electronics Corporation 功能描述:DEV MCU/8BIT CMOS EMULATION CHIP - Bulk |
| M37151M6 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。