參數資料
型號： M368L6423FTN
廠商： Sanken Electric Co.,Ltd.
英文描述： 184pin Unbuffered Module based on 256Mb F-die with 64/72-bit Non-ECC / ECC
中文描述： 184pin緩沖模塊，基于256Mb的F -死去64/72-bit非ECC / ECC的
文件頁數： 15/19頁
文件大小： 287K
代理商： M368L6423FTN
DDR SDRAM
Revision 1.0 December, 2003
256MB, 512MB DDR466 Unbuffered DIMM
System Notes :
a. Pullup slew rate is characteristized under the test conditions as shown in Figure 1.
Output
Test point
VSSQ
50
Figure 1 : Pullup slew rate test load
b. Pulldown slew rate is measured under the test conditions shown in Figure 2.
Output
Test point
VDDQ
50
Figure 2 : Pulldown slew rate test load
c. Pullup slew rate is measured between (VDDQ/2 - 320 mV +/- 250 mV)
Pulldown slew rate is measured between (VDDQ/2 + 320 mV +/- 250 mV)
Pullup and Pulldown slew rate conditions are to be met for any pattern of data, including all outputs switching and only one output
switching.
Example : For typical slew rate, DQ0 is switching
For minmum slew rate, all DQ bits are switching from either high to low, or low to high.
For Maximum slew rate, only one DQ is switching from either high to low, or low to high.
The remaining DQ bits remain the same as for previous state.
d. Evaluation conditions
Typical : 25
°
C (T Ambient), VDDQ = 2.6V, typical process
Minimum : 70
°
C (T Ambient), VDDQ = 2.5V, slow - slow process
Maximum : 0
°
C (T Ambient), VDDQ = 2.7V, fast - fast process
e. The ratio of pullup slew rate to pulldown slew rate is specified for the same temperature and voltage, over the entire temperature and
voltage range. For a given output, it represents the maximum difference between pullup and pulldown drivers due to process variation.
f. Verified under typical conditions for qualification purposes.
g. TSOPII package divices only.
h. A derating factor will be used to increase tIS and tIH in the case where the input slew rate is below 0.5V/ns
as shown in Table 2. The Input slew rate is based on the lesser of the slew rates detemined by either VIH(AC) to VIL(AC) or
VIH(DC) to VIL(DC), similarly for rising transitions.
i. A derating factor will be used to increase tDS and tDH in the case where DQ, DM, and DQS slew rates differ, as shown in Tables 3 & 4.
Input slew rate is based on the larger of AC-AC delta rise, fall rate and DC-DC delta rise, Input slew rate is based on the lesser of the
slew rates determined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions.
The delta rise/fall rate is calculated as:
{1/(Slew Rate1)} - {1/(Slew Rate2)}
For example : If Slew Rate 1 is 0.5 V/ns and slew Rate 2 is 0.4 V/ns, then the delta rise, fall rate is - 0.5ns/V . Using the table given, this
would result in the need for an increase in tDS and tDH of 100 ps.
相關PDF資料
PDF描述
M368L6423FTN-CB3B0 184pin Unbuffered Module based on 256Mb F-die with 64/72-bit Non-ECC / ECC
M368L6423DTM-CCC 184pin Unbuffered Module based on 256Mb D-die 64/72-bit Non ECC/ECC
M368L6423DTM-LCC 184pin Unbuffered Module based on 256Mb D-die 64/72-bit Non ECC/ECC
M368L6423ETM DDR SDRAM Unbuffered Module
M368L6423ETM-CCC4 DDR SDRAM Unbuffered Module
相關代理商/技術參數
參數描述
M368L6423FTN-CB3B0 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:184pin Unbuffered Module based on 256Mb F-die with 64/72-bit Non-ECC / ECC
M368L6423FTN-CCC00 制造商:Samsung Semiconductor 功能描述:256 DDR SDRAM MODUL X64 TSOP2-400 - Trays
M368L6423HUN 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:DDR SDRAM Product Guide
M368L6423JUN 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:DDR SDRAM Product Guide
M368L6523BTM-CCC 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:DDR SDRAM Unbuffered Module 184pin Unbuffered Module based on 512Mb B-die with 64/72-bit Non ECC/ECC 66 TSOP-II
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*