- 您現在的位置：買賣IC網 > PDF目錄98005 > M34554M8-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | M34554M8-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, QFP-64 |
| 文件頁數： | 98/137頁 |
| 文件大?。?/td> | 1606K |
| 代理商： | M34554M8-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁當前第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁
63
4554 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Writing to reload register R1, R3, R4H
When writing data to reload register R1, reload register R3 or re-
load regiser R4H while timer 1, timer 3 or timer 4 is operating,
avoid a timing when timer 1, timer 3 or timer 4 underflows.
Timer 4
Avoid a timing when timer 4 underflows to stop timer 4.
When “H” interval extension function of the PWM signal is set to
be “valid”, set “1” or more to reload register R4H.
Timer 5
Stop timer 5 counting to change its count source.
Timer input/output pin
Set the port C output latch to “0” to output the PWM signal from
C/CNTR pin.
Watchdog timer
The watchdog timer function is valid after system is released
from reset. When not using the watchdog timer function, execute
the DWDT instruction and the WRST instruction continuously,
and clear the WEF flag to “0” to stop the watchdog timer function.
The watchdog timer function is valid after system is returned from
the power down state. When not using the watchdog timer func-
tion, execute the DWDT instruction and the WRST instruction
continuously every system is returned from the power down
state, and stop the watchdog timer function.
When the watchdog timer function and power down function are
used at the same time, execute the WRST instruction before sys-
tem enters into the power down state and initialize the flag
WDF1.
Multifunction
Be careful that the output of ports D8 and D9 can be used even
when INT0 and INT1 pins are selected.
Be careful that the input/output of port D7 can be used even
when input of CNTR0 pin are selected.
Be careful that the input of port D7 can be used even when out-
put of CNTR0 pin are selected.
Be careful that the “H” output of port C can be used even when
output of CNTR1 pin are selected.
Program counter
Make sure that the PCH does not specify after the last page of
the built-in ROM.
LIST OF PRECAUTIONS
Noise and latch-up prevention
Connect a capacitor on the following condition to prevent noise
and latch-up;
connect a bypass capacitor (approx. 0.1
F) between pins VDD
and VSS at the shortest distance,
equalize its wiring in width and length, and
use relatively thick wire.
In the One Time PROM version, CNVSS pin is also used as VPP
pin. Accordingly, when using this pin, connect this pin to VSS
through a resistor about 5 k
(connect this resistor to CNVSS/
VPP pin as close as possible).
Register initial values 1
The initial value of the following registers are undefined after sys-
tem is released from reset. After system is released from reset,
set initial values.
Register Z (2 bits)
Register D (3 bits)
Register E (8 bits)
Register initial values 2
The initial value of the following registers are undefined at RAM back-
up. After system is returned from RAM back-up, set initial values.
Register Z (2 bits)
Register X (4 bits)
Register Y (4 bits)
Register D (3 bits)
Register E (8 bits)
Stack registers (SKS)
Stack registers (SKs) are eight identical registers, so that subrou-
tines can be nested up to 8 levels. However, one of stack
registers is used respectively when using an interrupt service
routine and when executing a table reference instruction. Accord-
ingly, be careful not to over the stack when performing these
operations together.
Prescaler
Stop counting and then execute the TABPS instruction to read
from prescaler data.
Stop counting and then execute the TPSAB instruction to set
prescaler data.
Timer count source
Stop timer 1, 2, 3, 4 and LC counting to change its count source.
Reading the count value
Stop timer 1, 2, 3 or 4 counting and then execute the data read
instruction (TAB1, TAB2, TAB3, TAB4) to read its data.
Writing to the timer
Stop timer 1, 2, 3, 4 or LC counting and then execute the data
write instruction (T1AB, T2AB, T3AB, T4AB, TLCA) to write its
data.
10
13
11
12
14
15
相關PDF資料 |
PDF描述 |
|---|---|
| M34554MC-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 |
| M34571G6FP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24 |
| M34584EDFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M35047-XXXSP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 |
| M35047-XXXFP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34554MC-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34556G8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34556G8HFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34556M4H-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34556M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。