- 您現在的位置：買賣IC網 > PDF目錄67761 > M34283G2-XXXGP 4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | M34283G2-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20 |
| 封裝： | 4.40 X 6.50 MM, 0.65 MM PITCH, PLASTIC, LSSOP-20 |
| 文件頁數： | 18/41頁 |
| 文件大?。?/td> | 441K |
| 代理商： | M34283G2-XXXGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
Rev.1.01
Mar 20, 2006
page 23 of 62
REJ03B0109-0101
4283 Group
LIST OF PRECAUTIONS
Noise and latch-up prevention
Connect a capacitor on the following condition to prevent noise
and latch-up;
connect a bypass capacitor (approx. 0.01
F) between pins
VDD and VSS at the shortest distance,
equalize its wiring in width and length, and
use the thickest wire.
Port E2 is also uesd as VPP pin. Connect this pin to VSS
through the resistor about 5k
which is assigned to E2/VPP
pin as close as possible at the shortest distance.
Register initial values 1
The initial value of the following registers are undefined after
system is released from reset. After system is released from
reset, set initial values.
Register D (3 bits)
Register E (8 bits)
Register initial values 2
The initial value of the following registers are undefined at RAM
backup. After system is returned from RAM back-up, set initial
values.
Register X (4 bits)
Register Y (4 bits)
Register D (3 bits)
Register E (8 bits)
Stack registers (SKS)
Stack registers (SKs) are four identical registers, so that
subroutines can be nested up to 4 levels. However, one of
stack registers is used respectively when using an interrupt
service routine and when executing a table reference
instruction. Accordingly, be careful not to over the stack when
performing these operations together.
Notes on unused pins
Timer
Count source
Stop timer 1 or timer 2 counting to change its count source.
Reading the count value
Stop timer 1 or 2 counting and then execute the data read
instruction (TAB1, TAB2) to read its data.
Watchdog timer
Be sure that the timing to execute the WRST instruction in
order to operate WDT efficiently.
Writing to reload register R1
When writing data to reload register R1 while timer 1 is
operating, avoid a timing when timer 1 underflows.
Timer 1 count operation
When the bit 5 of the watchdog timer (WDT) is selected as
the timer 1 count source, the error of maximum ± 256
s
(at the minimum instruction execution time : 8
s) is
generated from timer 1 start until timer 1 underflow. When
programming, be careful about this error.
Stop of timer 2
Avoid a timing when timer 2 underflows to stop timer 2.
Writing to reload register R2H
When writing data to reload register R2H while timer 2 is
operating, avoid a timing when timer underflows.
Timer 2 carrier wave output function
When to expand “H” interval of carrier wave is valid, set “1”
or more to reload register R2H.
Timer 1 and timer 2 carrier wave output function
Count starts from the rising edge in Fig. 29 after the first
falling edge of the count source, after timer 1 and timer 2
operations start ① in Fig. 29.
Time to first underflow ③ in Fig. 29 is different from time
among next underflow ④ in Fig. 29 by the timing to start the
timer and count source operations after count starts.
Pin
D0–D3
D4–D7
E0, E1
E2
G0–G3
CARR
Connection
Open.
Connect to VDD.
Open (Set the output latch to “1” ).
Open (Set the output latch to “0” ).
Connect to VDD.
Open (Set the output latch to “1” ).
Open (Set the output latch to “0” ).
Connect to VDD.
Open.
Connect to VSS.
Open (Set the output latch to “1” ).
Open (Set the output latch to “0” ).
Connect to VDD.
Open.
Usage condition
Pull-down transistor OFF.
(Note when connecting to VSS and VDD)
Connect the unused pins to VSS and VDD at the shortest
distance and use the thick wire against noise.
Fig. 29 Count start time and count time when operation
starts (T1, T2)
3
21
032
103
→
Timer start
Count source
Timer value
Timer underflow signal
Program counter
Make sure that the program counter does not specify after the
last page of the built-in ROM.
相關PDF資料 |
PDF描述 |
|---|---|
| M34502E4FP | 4-BIT, OTPROM, MICROCONTROLLER, PDSO24 |
| M34502M4-XXXFP | 4-BIT, MROM, MICROCONTROLLER, PDSO24 |
| M34502M2-XXXFP | 4-BIT, MROM, MICROCONTROLLER, PDSO24 |
| M34508G4GP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20 |
| M34508G4H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34286 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34286G2GP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34286G2GP#U0 | 功能描述:MCU 1.8/3.6V 2KB ROM 20-LSSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:720/4500 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| M34286G2GP#WC | 制造商:Renesas Electronics Corporation 功能描述:4BIT MCU |
| M34286G2-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。