參數資料
型號: M34250M2-116FP
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
中文描述: 單芯片4位微機的CMOS
文件頁數: 27/58頁
文件大小: 331K
代理商: M34250M2-116FP
MITSUBISHI
ELECTRIC
27
MITSUBISHI MICROCOMPUTERS
4250 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
Remarks
Select the return edge (rising edge or falling edge) with the bit 2 of register
K0 according to the external state before going into the RAM back-up
state.
Set the port using the key-on wakeup function selected with register K0
to “H” level before going into the RAM back-up state.
Return source
G
0
/INT pin
Ports G
1
–G
3
S
0
–S
3
Return condition
Return by an external rising edge
input (“L”
“H”) or falling edge
input (“H”
“L”).
The EXF0 flag is not set.
Return by an external “L” level
input.
Table 13 Return source and return condition
Note: G
0
/INT pin and ports G
1
–G
3
, S
0
–S
3
share the circuit which is used to detect the edge and to recognize “L” level.
The G
0
/INT pin cannot be set to “no key-on wakeup.”
RAM BACK-UP MODE
The 4250 Group has the RAM back-up mode.
When the POF instruction is executed continuously, system
enters the RAM back-up state.
As oscillation stops retaining RAM, the function of reset circuit
and states at RAM back-up mode, current dissipation can be
reduced without losing the contents of RAM. Table 12 shows
the function and states retained at RAM back-up. Figure 24 shows
the state transition.
(1) Identification of the start condition
Warm start (return from the RAM back-up state) or cold start
(return from the normal reset state) can be identified by
examining the state of the power down flag (P) with the SNZP
instruction.
(2) Warm start condition
When the external wakeup signal is input after the system
enters the RAM back-up state by executing the POF instruction
continuously, the CPU starts executing the software from
address 0 in page 0. In this case, the P flag is “1.”
(3) Cold start condition
The CPU starts executing the software from address 0 in page
0 when reset pulse is input to RESET pin.
In this case, the P flag is “0.”
(4) Return signal
An external wakeup signal is used to return from the RAM
back-up mode. Table 13 shows the return condition for each
return source.
Table 12 Functions and states retained at RAM back-up
Function
Program counter (PC), registers A, B,
carry flag (CY), stack pointer (SP) (Note 2)
Contents of RAM
Port
Timer control register V1
Timer 1 function
Pull-up control register PU0
Key-on wakeup control register K0
Logic operation selection register LO
External interrupt request flag (EXF0)
Timer 1 interrupt request flag (T1F)
Interrupt enable flag (INTE)
Notes 1: “O” represents that the function can be retained, and
” represents that the function is initialized.
Registers and flags other than the above are undefined
at RAM back-up, and set an initial value after returning.
2:The stack pointer (SP) points the level of the stack
register and is initialized to “3” at RAM back-up.
RAM back-up
O
O
O
相關PDF資料
PDF描述
M34250 Single Chip 4 Bits CMOS Microcomputer(4位單片機)
M34250E2FP SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34250M2 SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34282M2-064GP Aluminum Electrolytic Capacitor; Capacitor Type:Computer Grade; Voltage Rating:75VDC; Capacitor Dielectric Material:Aluminum Electrolytic; Operating Temperature Range:-40 C to C; Capacitance:68000uF RoHS Compliant: Yes
M34282M1 SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M34250M2-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3426 SL002 制造商:Alpha Wire 功能描述:CBL 8PR 24AWG SLT 500'
M3426 SL005 制造商:Alpha Wire 功能描述:CBL 8PR 24AWG SLT 100'
M3427-SLATE-500 制造商:Alpha Wire 功能描述:
M3428 SL001 制造商:Alpha Wire 功能描述:CBL 12PR 24AWG SLT 1000'