參數資料
型號: M30843FJTGP
元件分類: 微控制器/微處理器
英文描述: 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100
封裝: 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100
文件頁數: 61/91頁
文件大?。?/td> 903K
代理商: M30843FJTGP
63
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e parametric
limits
are
subject
to
change.
Table 13 Definition of each bit in status register
Status Register
The status register shows the operating status of the flash
memory and whether erase operations and programs ended suc-
cessfully or in error. It can be read in the following ways:
(1) By reading an arbitrary address from the User ROM area after
writing the read status register command (7016)
(2) By reading an arbitrary address from the User ROM area in the
period from when the program starts or erase operation starts
to when the read array command (FF16) is input.
Also, the status register can be cleared by writing the clear status
register command (5016).
After reset, the status register is set to “8016”.
Table 13 shows the status register. Each bit in this register is ex-
plained below.
Sequencer status (SR7)
The sequencer status indicates the operating status of the flash
memory. This bit is set to “0” (busy) during write or erase operation
and is set to “1” when these operations ends.
After power-on, the sequencer status is set to “1” (ready).
Erase status (SR5)
The erase status indicates the operating status of erase operation.
If an erase error occurs, it is set to “1”. When the erase status is
cleared, it is reset to “0”.
Program status (SR4)
The program status indicates the operating status of write opera-
tion. When a write error occurs, it is set to “1”.
The program status is reset to “0” when it is cleared.
If “1” is written for any of the SR5 and SR4 bits, the read array,
program, and block erase commands are not accepted. Before ex-
ecuting these commands, execute the clear status register
command (5016) and clear the status register.
Also, if any commands are not correct, both SR5 and SR4 are set
to “1”.
Each bit of
SRD bits
SR7 (bit7)
SR6 (bit6)
SR5 (bit5)
SR4 (bit4)
SR3 (bit3)
SR2 (bit2)
SR1 (bit1)
SR0 (bit0)
Sequencer status
Reserved
Erase status
Program status
Reserved
Status name
“1”
Ready
-
Terminated normally
-
“0”
Busy
-
Terminated normally
-
Definition
相關PDF資料
PDF描述
M30843MW-XXXFP 32-BIT, MROM, 32 MHz, MICROCONTROLLER, PQFP100
M30845FHTGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP144
M30840ME-XXXGP 32-BIT, MROM, 32 MHz, MICROCONTROLLER, PQFP100
M30843FWTGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100
M30843FJGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M30843FWGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16/32-BIT CMOS MICROCOMPUTER
M30843FWGP#D3 制造商:Renesas Electronics Corporation 功能描述:MCU 16BIT R8C CISC 320KB FLASH 5V 100LQFP - Trays
M30843FWGP#D5 制造商:Renesas Electronics Corporation 功能描述:MCU 16BIT R8C CISC 320KB FLASH 5V 100LQFP - Trays
M30843FWGP#U3 功能描述:IC M32C MCU FLASH 320K 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:M16C™ M32C/80/84 標準包裝:1 系列:AVR® ATmega 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C,SPI,UART/USART 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:32 程序存儲器容量:32KB(16K x 16) 程序存儲器類型:閃存 EEPROM 大小:1K x 8 RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:44-TQFP 包裝:剪切帶 (CT) 其它名稱:ATMEGA324P-B15AZCT
M30843FWGP#U5 功能描述:IC M32C MCU FLASH 320K 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:M16C™ M32C/80/84 標準包裝:96 系列:PIC® 16F 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:I²C,SPI 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:11 程序存儲器容量:3.5KB(2K x 14) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):2.3 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 包裝:管件