參數資料
型號: M29W040-150K5R
廠商: 意法半導體
英文描述: Dual Low-Noise High-Speed Precision Operational Amplifier 8-PDIP
中文描述: 4兆位512KB的× 8,統一座低電壓單電源閃存
文件頁數: 5/31頁
文件大?。?/td> 205K
代理商: M29W040-150K5R
Mne.
Instr.
Cyc.
1st Cyc. 2nd Cyc. 3rd Cyc. 4th Cyc. 5th Cyc.
6th Cyc.
7th Cyc.
RST
(3,9)
Read Array/
Reset
1+
Addr.
(2,6)
X
Read Memory Array until a new write cycle is initiated.
Data
F0h
3+
Addr.
(2,6)
5555h
2AAAh
5555h
Read Memory Array until a new write
cycle isinitiated.
Data
AAh
55h
F0h
RSIG
(3)
Read
Electronic
Signature
3+
Addr.
(2,6)
5555h
2AAAh
5555h
Read Electronic Signature until a new
write cycle is initiated. See Note 4.
Data
AAh
55h
90h
RBP
(3)
Read Block
Protection
3+
Addr.
(2,6)
5555h
2AAAh
5555h
Read BlockProtection until a new write
cycle isinitiated. See Note 5.
Data
AAh
55h
90h
PG
Program
4
Addr.
(2,6)
5555h
2AAAh
5555h
Program
AddressRead Data Pollingor Toggle Bit
until Program completes.
Program
Data
Data
AAh
55h
A0h
BE
Block Erase
6
Addr.
(2,6)
5555h
2AAAh
5555h
5555h
2AAAh
Block
Address
Additional
Block
(7)
Data
AAh
55h
80h
AAh
55h
30h
30h
CE
Chip Erase
6
Addr.
(2,6)
5555h
2AAAh
5555h
5555h
2AAAh
5555h
Note 8
Data
AAh
55h
80h
AAh
55h
10h
ES
Erase
Suspend
1
Addr.
(2,6)
X
Read until Togglestops, then read all the data needed from any
uniform block(s) not being erased then Resume Erase.
Data
B0h
ER
Erase
Resume
1
Addr.
(2,6)
X
Read Data Polling or Toggle Bit until Erase completes or Erase
is suspended another time
Data
30h
PD
(10)
Power
Down
1
Addr.
(2,6)
5555h
Puts the memory in Power Down mode where power
consumption is reducedto typically less than 1
μ
A
Data
20h
Notes:
1. Command not interpreted in this table will default to read array mode.
2. X = Don’tCare.
3. The first cycle of the RST,RBP or RSIG instruction is followed by read operations to read memory array,Status Register or
Electronic Signature codes. Any number of read cycles can occur after one command cycle.
4. Signature Address bits A0, A1, A6 at V
IL
will outputManufacturer code (20h). Address bits A0at V
IH
andA1, A6 atV
IL
will output
Device code.
5. Protection Address: A0, A6 at V
IL
, A1at V
IH
and A16,A17, A18 within the uniform block to be checked,will outputthe
Block Protectionstatus.
6. Address bits A15-A18are don’tcare forcoded address inputs.
7. Optional, additional blocks addresses must be entered within a 80
μ
s delay afterlast write entry, timeout status can be verified
through DQ3 value. When full command is entered, read Data Polling or Toggle bit until Erase is completed or suspended.
8. Read Data Polling or Toggle bit until Erase completes.
9. Await time of 5
μ
s is necessary after a Reset command, if the memory is in a Block Erase or PowerDown status, before
starting any operation.
10. Writing an RST command to theP/E.C. is mandatory prior to any new operation when the memory is in PowerDown mode.
Table6. Instructions
(1)
5/31
M29W040
相關PDF資料
PDF描述
M29W040-150K5TR Excalibur Low-Noise High-Speed Precision Dual Operational Amplifier 8-SOIC
M29W040-150K6R Excalibur Low-Noise High-Speed Precision Dual Operational Amplifier 8-SOIC
M29W040-150K6TR Excalibur Low-Noise High-Speed Precision Dual Operational Amplifier 8-SOIC
M29W040-150N1R Excalibur Low-Noise High-Speed Precision Dual Operational Amplifier 8-SOIC
M29W040-150N1TR 4 Mbit 512Kb x8, Uniform Block Low Voltage Single Supply Flash Memory
相關代理商/技術參數
參數描述
M29W040-150K5TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block Low Voltage Single Supply Flash Memory
M29W040-150K6R 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block Low Voltage Single Supply Flash Memory
M29W040-150K6TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block Low Voltage Single Supply Flash Memory
M29W040-150N1R 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block Low Voltage Single Supply Flash Memory
M29W040-150N1TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block Low Voltage Single Supply Flash Memory