- 您現在的位置：買賣IC網 > PDF目錄359024 > M29F016B70N6T (意法半導體) 16 Mbit 2Mb x8, Uniform Block Single Supply Flash Memory PDF資料下載
參數資料
| 型號： | M29F016B70N6T |
| 廠商： | 意法半導體 |
| 英文描述： | 16 Mbit 2Mb x8, Uniform Block Single Supply Flash Memory |
| 中文描述： | 16兆位的2Mb × 8，統一座單電源閃存 |
| 文件頁數： | 7/22頁 |
| 文件大?。?/td> | 135K |
| 代理商： | M29F016B70N6T |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁
7/22
M29F016B
Table 5. Commands
Note: X Don’t Care, PA Program Address, PD Program Data, BA Any address in the Block.
All values in the table are in hexadecimal.
The Command Interface only uses address bits A0-A10 to verify the commands, the upper address bits are Don’t Care.
Read/Reset.
After a Read/Reset command, read the memory as normal until another command is issued.
Auto Select.
After an Auto Select command, read Manufacturer ID, Device ID or Block Protection Status.
Program, Unlock Bypass Program, Chip Erase, Block Erase.
After these commands read the Status Register until the Program/Erase
Controller completes and the memory returns to Read Mode. Add additional Blocks during Block Erase Command with additional Bus Write
Operations until the Timeout Bit is set.
Unlock Bypass.
After the Unlock Bypass command issue Unlock Bypass Program or Unlock Bypass Reset commands.
Unlock Bypass Reset.
After the Unlock Bypass Reset command read the memory as normal until another command is issued.
Erase Suspend.
After the Erase Suspend command read non-erasing memory blocks as normal, issue AutoSelect and Program commands
on non-erasing blocks as normal.
Erase Resume.
After the Erase Resume command the suspended Erase operation resumes, read the Status Register until the Program/
Erase Controller completes and the memory returns to Read Mode.
Command
L
Bus Write Operations
1st
2nd
3rd
4th
5th
6th
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Read/Reset
1
X
F0
3
555
AA
2AA
55
X
F0
Auto Select
3
555
AA
2AA
55
555
90
Program
4
555
AA
2AA
55
555
A0
PA
PD
Unlock Bypass
3
555
AA
2AA
55
555
20
Unlock Bypass
Program
2
X
A0
PA
PD
Unlock Bypass Reset
2
X
90
X
00
Chip Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
555
10
Block Erase
6+
555
AA
2AA
55
555
80
555
AA
2AA
55
BA
30
Erase Suspend
1
X
B0
Erase Resume
1
X
30
Unlock Bypass Command.
The Unlock Bypass
command is used in conjunction with the Unlock
Bypass Program command to program the memo-
ry. When the access time to the device is long (as
with some EPROM programmers) considerable
time saving can be made by using these com-
mands. Three Bus Write operations are required
to issue the Unlock Bypass command.
Once the Unlock Bypass command has been is-
sued the memory will only accept the Unlock By-
pass Program command and the Unlock Bypass
Reset command. The memory can be readas if in
Read mode.
Unlock Bypass Program Command.
The Unlock
Bypass Program command can be used to pro-
gram one address in memory at a time. The com-
mand requires two Bus Write operations, the final
write operation latches the address and datain the
internal state machine and starts the Program/
Erase Controller.
The Program operation using the Unlock Bypass
Program command behaves identically to the Pro-
gram operation using the Program command. A
protected block cannot be programmed; the oper-
ation cannot be aborted and theStatus Register is
read. Errors must be reset using the Read/Reset
command, which leaves the device in Unlock By-
pass Mode. See the Program command for details
on the behavior.
Unlock Bypass Reset Command.
The
Bypass Reset command can be used to return to
Read/Reset mode from Unlock Bypass Mode.
TwoBus Write operationsare required toissue the
Unlock Bypass Reset command.
Unlock
相關PDF資料 |
PDF描述 |
|---|---|
| M29F016D | 16 Mbit (2Mb x8, Uniform Block) 5V Supply Flash Memory |
| M29F016D55M1T | 16 Mbit (2Mb x8, Uniform Block) 5V Supply Flash Memory |
| M29F016D55M6T | 16 Mbit (2Mb x8, Uniform Block) 5V Supply Flash Memory |
| M29F016D55N1T | 16 Mbit (2Mb x8, Uniform Block) 5V Supply Flash Memory |
| M29F016D55N6T | 16 Mbit (2Mb x8, Uniform Block) 5V Supply Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M29F016B90M1 | 功能描述:閃存 16M (2Mx8) 90ns RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M29F016B90M1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block Single Supply Flash Memory |
| M29F016B90M3T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block Single Supply Flash Memory |
| M29F016B90M6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block Single Supply Flash Memory |
| M29F016B90N1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block Single Supply Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。