- 您現在的位置：買賣IC網 > PDF目錄299432 > M27C160-50K1TR (STMICROELECTRONICS) 1M X 16 OTPROM, 50 ns, PQCC44 PDF資料下載
參數資料
| 型號： | M27C160-50K1TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 1M X 16 OTPROM, 50 ns, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 3/26頁 |
| 文件大?。?/td> | 267K |
| 代理商： | M27C160-50K1TR |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
M27C160
Device description
ambient temperature range that is required when programming the M27C160. To activate
the ES mode, the programming equipment must force 11.5V to 12.5V on address line A9 of
the M27C160, with VPP = VCC = 5V. Two identifier bytes may then be sequenced from the
device outputs by toggling address line A0 from VIL to VIH. All other address lines must be
held at VIL during Electronic Signature mode. Byte 0 (A0 = VIL) represents the manufacturer
code and byte 1 (A0 = VIH) the device identifier code. For the STMicroelectronics M27C160,
these two identifier bytes are given in Table 3 and can be read-out on outputs Q7 to Q0.
Note:
Outputs Q15-Q8 are set to '0'.
2.10
Erasure operation (applies to UV EPROM)
The erasure characteristics of the M27C160 is such that erasure begins when the cells are
exposed to light with wavelengths shorter than approximately 4000 . It should be noted
that sunlight and some type of fluorescent lamps have wavelengths in the 3000-4000
range. Research shows that constant exposure to room level fluorescent lighting could
erase a typical M27C160 in about 3 years, while it would take approximately 1 week to
cause erasure when exposed to direct sunlight. If the M27C160 is to be exposed to these
types of lighting conditions for extended periods of time, it is suggested that opaque labels
be put over the M27C160 window to prevent unintentional erasure. The recommended
erasure procedure for M27C160 is exposure to short wave ultraviolet light which has a
wavelength of 2537 . The integrated dose (i.e. UV intensity x exposure time) for erasure
should be a minimum of 30 W-sec/cm2. The erasure time with this dosage is approximately
30 to 40 minutes using an ultraviolet lamp with 12000 W/cm2 power rating. The M27C160
should be placed within 2.5cm (1 inch) of the lamp tubes during the erasure. Some lamps
have a filter on their tubes which should be removed before erasure.
Table 3.
Electronic Signature
Identifier
A0
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
Hex Data
Manufacturer’s Code
VIL
00100000
20h
Device Code
VIH
10110001
B1h
相關PDF資料 |
PDF描述 |
|---|---|
| M27C512-20N6E | 64K X 8 OTPROM, 200 ns, PDSO28 |
| M27C512-20XN6F | 64K X 8 OTPROM, 200 ns, PDSO28 |
| M27C512-45N1E | 64K X 8 OTPROM, 45 ns, PDSO28 |
| M27C512-80XC1E | 64K X 8 OTPROM, 80 ns, PQCC32 |
| M27C64A-15K6X | 8K X 8 OTPROM, 150 ns, PQCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M27C160-70XF1 | 功能描述:可擦除可編程ROM 2Mx8 or 1Mx16 70ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| M27C160-90B1 | 功能描述:可擦除可編程ROM 2Mx8 or 1Mx16 90ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| M27C160-90F1 | 功能描述:可擦除可編程ROM 2Mx8 or 1Mx16 90ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| M27C2001-10B1 | 功能描述:可擦除可編程ROM 2M (256Kx8) 100ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| M27C2001-10B1 | 制造商:STMicroelectronics 功能描述:PROM OTP CMOS 2MB 27C2001 DIP32 |
發布緊急采購，3分鐘左右您將得到回復。