- 您現在的位置：買賣IC網 > PDF目錄358986 > M27C1001-25C3X (意法半導體) IC Socket Test Clip; No. of Contacts:1 RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | M27C1001-25C3X |
| 廠商： | 意法半導體 |
| 英文描述： | IC Socket Test Clip; No. of Contacts:1 RoHS Compliant: Yes |
| 中文描述： | 1兆位存儲器的128KB x8紫外線和OTP存儲器 |
| 文件頁數： | 4/17頁 |
| 文件大?。?/td> | 159K |
| 代理商： | M27C1001-25C3X |
M27C1001
4/17
DEVICE OPERATION
The operating modes of the M27C1001 are listed
in the Operating Modes table. A single power sup-
ply is required in the read mode. All inputs are TTL
levels except for V
PP
and 12V on A9 for Electronic
Signature.
Read Mode
The M27C1001 has two control functions, both of
which must be logically active in order to obtain
data at the outputs. Chip Enable (E) is the power
control and should be used for device selection.
Output Enable (G) is the output control and should
be used to gate data to the output pins, indepen-
dent of device selection. Assuming that the ad-
dresses are stable, the address access time
(t
AVQV
) is equal to the delay from E to output
(t
ELQV
). Data is available at the output after a delay
of t
GLQV
from the falling edge of G, assuming that
E has been low and the addresses have been sta-
ble for at least t
AVQV
-t
GLQV
.
Standby Mode
The M27C1001 has a standby mode which reduc-
es the supply current from 30mA to 100μA. The
M27C1001 is placed in the standby mode by ap-
plying a CMOS high signal to the E input. When in
the standby mode, the outputs are in a high imped-
ance state, independent of the G input.
Table 5. AC Measurement Conditions
High Speed
Standard
Input Rise and Fall Times
≤
10ns
≤
20ns
Input Pulse Voltages
0 to 3V
0.4V to 2.4V
Input and Output Timing Ref. Voltages
1.5V
0.8V and 2V
Figure 3. AC Testing Input Output Waveform
AI01822
3V
High Speed
0V
1.5V
2.4V
Standard
0.4V
2.0V
0.8V
Figure 4. AC Testing Load Circuit
AI01823B
1.3V
OUT
CL
CL = 30pF for High Speed
CL = 100pF for Standard
CL includes JIG capacitance
3.3k
1N914
DEVICE
UNDER
TEST
Table 6. Capacitance
(1)
(T
A
= 25 °C, f = 1 MHz)
Symbol
Note: 1. Sampled only, not 100% tested.
Parameter
Test Condition
Min
Max
Unit
C
IN
Input Capacitance
V
IN
= 0V
6
pF
C
OUT
Output Capacitance
V
OUT
= 0V
12
pF
相關PDF資料 |
PDF描述 |
|---|---|
| M27C1001-45N1X | 1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-35N1X | 1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-20N1X | LED, ALINGAP, YELLOW, CLR, 1206, SMD |
| M27C1001-15N1X | 1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-12N1X | 1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M27C1001-25C6TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-25C6X | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-25CTR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Mbit (128 Kbit x 8) UV EPROM and OTP EPROM |
| M27C1001-25F1 | 功能描述:可擦除可編程ROM DISC BY STM 2/02 DIP-32 128KX8 250NS RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| M27C1001-25F1TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
發布緊急采購，3分鐘左右您將得到回復。