參數資料
型號: M25PE10-VMN6P
廠商: 意法半導體
元件分類: DRAM
英文描述: 4 Mbit Uniform Sector, Serial Flash Memory
中文描述: 4兆位統一部門,串行閃存
文件頁數: 33/60頁
文件大?。?/td> 310K
代理商: M25PE10-VMN6P
M25PE20, M25PE10
Instructions
33/60
6.9
Page Write (PW)
The Page Write (PW) instruction allows Bytes to be written in the memory. Before it can be
accepted, a Write Enable (WREN) instruction must previously have been executed. After the
Write Enable (WREN) instruction has been decoded, the device sets the Write Enable Latch
(WEL).
The Page Write (PW) instruction is entered by driving Chip Select (S) Low, followed by the
instruction code, three address Bytes and at least one data Byte on Serial Data Input (D).
The rest of the page remains unchanged if no power failure occurs during this write cycle.
The Page Write (PW) instruction performs a page erase cycle even if only one Byte is
updated.
If the 8 least significant address bits (A7-A0) are not all zero, all transmitted data exceeding
the addressed page boundary roll over, and are written from the start address of the same
page (the one whose 8 least significant address bits (A7-A0) are all zero). Chip Select (S)
must be driven Low for the entire duration of the sequence.
The instruction sequence is shown in
Figure 16
.
If more than 256 Bytes are sent to the device, previously latched data are discarded and the
last 256 data Bytes are guaranteed to be written correctly within the same page. If less than
256 Data Bytes are sent to device, they are correctly written at the requested addresses
without having any effects on the other Bytes of the same page.
For optimized timings, it is recommended to use the Page Write (PW) instruction to write all
consecutive targeted Bytes in a single sequence versus using several Page Write (PW)
sequences with each containing only a few Bytes (see
Table 22: AC characteristics (50 MHz
operation, T9HX (0.11μm) process)
).
Chip Select (S) must be driven High after the eighth bit of the last data Byte has been
latched in, otherwise the Page Write (PW) instruction is not executed.
As soon as Chip Select (S) is driven High, the self-timed Page Write cycle (whose duration
is t
PW
) is initiated. While the Page Write cycle is in progress, the Status Register may be
read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is
1 during the self-timed Page Write cycle, and is 0 when it is completed. At some unspecified
time before the cycle is complete, the Write Enable Latch (WEL) bit is reset.
A Page Write (PW) instruction applied to a page that is Hardware Protected is not executed.
Any Page Write (PW) instruction, while an Erase, Program or Write cycle is in progress, is
rejected without having any effects on the cycle that is in progress.
相關PDF資料
PDF描述
M25PE10-VMP6G 4 Mbit Uniform Sector, Serial Flash Memory
M25PE10-VMP6P 4 Mbit Uniform Sector, Serial Flash Memory
M25PE10-VMP6TG 4 Mbit Uniform Sector, Serial Flash Memory
M25PE10-VMP6TP 4 Mbit Uniform Sector, Serial Flash Memory
M25PE20_07 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
M25PE10-VMN6TG 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1 and 2 Mbit, page-erasable serial Flash memories with byte alterability, 75 MHz SPI bus, standard pinout
M25PE10-VMN6TP 功能描述:電可擦除可編程只讀存儲器 SERIAL PAGE ERASE FLASH 1 Mbit Datas RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M25PE10-VMN6TPBA 制造商:Micron Technology Inc 功能描述:SERIAL NOR 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3V/3.3V 1Mbit 128K x 8bit 8ns T/R 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel
M25PE10-VMN6TPBA TR 制造商:Micron Technology Inc 功能描述:IC FLASH 1MBIT 75MHZ 8SO
M25PE10-VMP6G 制造商:Micron Technology Inc 功能描述:FLASH SERL-SPI 3.3V 1MBIT 128KX8 8NS 8PIN VDFPN EP - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 1MBIT 75MHZ 8VFQFPN