- 您現在的位置：買賣IC網 > PDF目錄358974 > M25P64-VMF6G (意法半導體) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | M25P64-VMF6G |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 23/38頁 |
| 文件大?。?/td> | 519K |
| 代理商： | M25P64-VMF6G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
23/38
M25P64
Sector Erase (SE)
The Sector Erase (SE) instruction sets to 1 (FFh)
all bits inside the chosen sector. Before it can be
accepted, a Write Enable (WREN) instruction
must previously have been executed. After the
Write Enable (WREN) instruction has been decod-
ed, the device sets the Write Enable Latch (WEL).
The Sector Erase (SE) instruction is entered by
driving Chip Select (S) Low, followed by the in-
struction code, and three address bytes on Serial
Data Input (D). Any address inside the Sector (see
Table 3.
) is a valid address for the Sector Erase
(SE) instruction. Chip Select (S) must be driven
Low for the entire duration of the sequence.
The instruction sequence is shown in
Figure 17.
.
Chip Select (S) must be driven High after the
eighth bit of the last address byte has been latched
in, otherwise the Sector Erase (SE) instruction is
not executed. As soon as Chip Select (S) is driven
High, the self-timed Sector Erase cycle (whose du-
ration is t
SE
) is initiated. While the Sector Erase cy-
cle is in progress, the Status Register may be read
to check the value of the Write In Progress (WIP)
bit. The Write In Progress (WIP) bit is 1 during the
self-timed Sector Erase cycle, and is 0 when it is
completed. At some unspecified time before the
cycle is completed, the Write Enable Latch (WEL)
bit is reset.
A Sector Erase (SE) instruction applied to a page
which is protected by the Block Protect (BP2, BP1,
BP0) bits (see
Table 2.
and
Table 3.
) is not execut-
ed.
Figure 17. Sector Erase (SE)
Instruction Sequence
Note: Address bit A23 is Don’t Care.
24 Bit Address
C
D
AI03751D
S
2
1
3
4
5
6
7
8
9
29 30 31
Instruction
0
23 22
2
0
1
MSB
相關PDF資料 |
PDF描述 |
|---|---|
| M25P64-VMF6 | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P64-VME6TP | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P64-VME6TG | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P64-VME6T | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P64-VME6P | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M25P64VMF6P | 制造商:NUMO 功能描述: |
| M25P64-VMF6P | 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M25P64-VMF6P | 制造商:Micron Technology Inc 功能描述:SEMICONDUCTOR: PENDING |
| M25P64-VMF6PBA | 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3.3V 64Mbit 8M x 8bit 8ns 16-Pin SOIC W Tray 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Trays 制造商:Micron Technology 功能描述:NOR Flash Serial-SPI 3.3V 64Mbit 8M x 8bit 8ns 16-Pin SOIC W Tray |
| M25P64-VMF6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Mbit, Low Voltage, Serial Flash Memory With 50MHz SPI Bus Interface |
發布緊急采購，3分鐘左右您將得到回復。