參數資料
型號： M25P16-VMW3TP
廠商： 意法半導體
元件分類： DRAM
英文描述： 4 Mbit Uniform Sector, Serial Flash Memory
中文描述： 4兆位統一部門，串行閃存
文件頁數： 28/55頁
文件大小： 335K
代理商： M25P16-VMW3TP
Instructions
M25P16
28/55
6.8
Page Program (PP)
The Page Program (PP) instruction allows bytes to be programmed in the memory
(changing bits from 1 to 0). Before it can be accepted, a Write Enable (WREN) instruction
must previously have been executed. After the Write Enable (WREN) instruction has been
decoded, the device sets the Write Enable Latch (WEL).
The Page Program (PP) instruction is entered by driving Chip Select (S) Low, followed by
the instruction code, three address bytes and at least one data byte on Serial Data Input (D).
If the 8 least significant address bits (A7-A0) are not all zero, all transmitted data that goes
beyond the end of the current page are programmed from the start address of the same
page (from the address whose 8 least significant bits (A7-A0) are all zero). Chip Select (S)
must be driven Low for the entire duration of the sequence.
The instruction sequence is shown in
Figure 15
.
If more than 256 bytes are sent to the device, previously latched data are discarded and the
last 256 data bytes are guaranteed to be programmed correctly within the same page. If less
than 256 Data bytes are sent to device, they are correctly programmed at the requested
addresses without having any effects on the other bytes of the same page.
For optimized timings, it is recommended to use the Page Program (PP) instruction to
program all consecutive targeted Bytes in a single sequence versus using several Page
Program (PP) sequences with each containing only a few Bytes (see
Table 15: AC
characteristics (Grade 6)
).
Chip Select (S) must be driven High after the eighth bit of the last data byte has been
latched in, otherwise the Page Program (PP) instruction is not executed.
As soon as Chip Select (S) is driven High, the self-timed Page Program cycle (whose
duration is t
PP
) is initiated. While the Page Program cycle is in progress, the Status Register
may be read to check the value of the Write In Progress (WIP) bit. The Write In Progress
(WIP) bit is 1 during the self-timed Page Program cycle, and is 0 when it is completed. At
some unspecified time before the cycle is completed, the Write Enable Latch (WEL) bit is
reset.
A Page Program (PP) instruction applied to a page which is protected by the Block Protect
(BP2, BP1, BP0) bits (see
Table 2
and
Table 3
) is not executed.
相關PDF資料
PDF描述
M25P16-VMW6G 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMW6P 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMW6TG 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMW6TP 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VME3G 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
M25P16-VMW6 制造商:Micron Technology Inc 功能描述:16 MBIT, SERIAL FLASH MEMORY, 75 MHZ SPI BUS INTERFACE - Bulk
M25P16-VMW6G 功能描述:閃存 16MBIT SFLASH MEM RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M25P16-VMW6P 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit, low voltage, Serial Flash memory with 50 MHz SPI bus interface
M25P16-VMW6T 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:16 Mbit, serial Flash memory, 75 MHz SPI bus interface
M25P16-VMW6TG 功能描述:閃存 16MBIT SFLASH MEM RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*