- 您現在的位置：買賣IC網 > PDF目錄296347 > M24256-BFMB6TG/K (STMICROELECTRONICS) 32K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | M24256-BFMB6TG/K |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 32K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| 封裝： | 2 X 3 MM, ROHS COMPLIANT, UFDFPN-8 |
| 文件頁數： | 42/42頁 |
| 文件大小： | 501K |
| 代理商： | M24256-BFMB6TG/K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁
M24256-BF, M24256-BR, M24256-BW, M24256-DR
Signal description
Doc ID 6757 Rev 21
2.5
VSS ground
VSS is the reference for the VCC supply voltage.
2.6
Supply voltage (VCC)
2.6.1
Operating supply voltage VCC
Prior to selecting the memory and issuing instructions to it, a valid and stable VCC voltage
Table 10). In order to secure a stable DC supply voltage, it is recommended to decouple the
VCC line with a suitable capacitor (usually of the order of 10 nF to 100 nF) close to the
VCC/VSS package pins.
This voltage must remain stable and valid until the end of the transmission of the instruction
and, for a Write instruction, until the completion of the internal write cycle (tW).
2.6.2
Power-up conditions
and the rise time must not vary faster than 1 V/s.
2.6.3
Device reset
In order to prevent inadvertent write operations during power-up, a power on reset (POR)
circuit is included. At power-up, the device does not respond to any instruction until VCC
reaches an internal reset threshold voltage. This threshold is lower than the minimum VCC
operating voltage defined in Table 8, Table 9 and Table 10.
When VCC passes over the POR threshold, the device is reset and enters the Standby
Power mode. However, the device must not be accessed until VCC reaches a valid and
stable VCC voltage within the specified [VCC(min), VCC(max)] range.
In a similar way, during power-down (continuous decrease in VCC), as soon as VCC drops
below the power on reset threshold voltage, the device stops responding to any instruction
sent to it.
2.6.4
Power-down conditions
During power-down (where VCC decreases continuously), the device must be in the Standby
Power mode (mode reached after decoding a Stop condition, assuming that there is no
internal Write cycle in progress).
相關PDF資料 |
PDF描述 |
|---|---|
| M24308/4-260 | 15 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR |
| M24308/4-2 | 15 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR |
| M24308/4-303 | 15 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR |
| M24308/4-325 | 15 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR |
| M24308/4-261 | 25 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M24256-BFMC6TG | 功能描述:電可擦除可編程只讀存儲器 256kB Serial I2C 3-Chip Enable 1 MHz RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M24256-BHR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:512 Kbit and 256 Kbit serial IC bus EEPROM with three Chip Enable lines |
| M24256-BHRDW6TP | 功能描述:電可擦除可編程只讀存儲器 512 Kbit/256 Kbit serial 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M24256-BHRMN6P | 功能描述:電可擦除可編程只讀存儲器 512Kbit and 256Kbit bus 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M24256-BHRMN6TP | 功能描述:電可擦除可編程只讀存儲器 513 Kbit/256 Kbit serial 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。