- 您現在的位置：買賣IC網 > PDF目錄358969 > M24128-WBN6T (意法半導體) 256/128 Kbit Serial IC Bus EEPROM Without Chip Enable Lines PDF資料下載
7/17
M24256, M24128
During the internal write cycle, the SDA input is
disabled internally, and the device does not re-
spond to any requests.
Minimizing System Delays by Polling On ACK
During the internal write cycle, the memory discon-
nects itself from the bus, and copies the data from
its internal latches to the memory cells. The maxi-
mum write time (t
w
) is shown in Table 10, but the
typical time is shorter. To make use of this, an Ack
polling sequence can be used by the master.
The sequence, as shown in Figure 7, is:
– Initial condition: a Write is in progress.
– Step 1: the master issues a START condition
followed by a Device Select Code (the first byte
of the new instruction).
– Step 2: if the memory is busy with the internal
write cycle, no Ack will be returned and the mas-
ter goes back to Step 1. If the memory has ter-
will fit up to the end of the row, a condition known
as ‘roll-over’ occurs. Data starts to become over-
written (in a way not formally specified in this data
sheet).
The master sends from one up to 64 bytes of data,
each of which is acknowledged by the memory if
the WC pin is low. If the WC pin is high, the con-
tents of the addressed memory location are not
modified, and each data byte is followed by a
NoAck. After each byte is transferred, the internal
byte address counter (the 6 least significant bits
only) is incremented. The transfer is terminated by
the master generating a STOP condition.
When the master generates a STOP condition im-
mediately after the Ack bit (in the “10
th
bit” time
slot), either at the end of a byte write or a page
write, the internal memory write cycle is triggered.
A STOP condition at any other time does not trig-
ger the internal write cycle.
Figure 7. Write Cycle Polling Flowchart using ACK
WRITE Cycle
in Progress
AI01847C
Next
Operation is
Addressing the
Memory
START Condition
DEVICE SELECT
with RW = 0
ACK
Returned
YES
NO
YES
NO
ReSTART
STOP
DATA for the
WRITE Operation
DEVICE SELECT
with RW = 1
Send Address
and Receive ACK
First byte of instruction
with RW = 0 already
decoded by the device
YES
NO
START
Condition
Continue the
WRITE Operation
Continue the
Random READ Operation
相關PDF資料 |
PDF描述 |
|---|---|
| M24128-WBN5T | 256/128 Kbit Serial IC Bus EEPROM Without Chip Enable Lines |
| M24128-MW6T | 256/128 Kbit Serial IC Bus EEPROM Without Chip Enable Lines |
| M24128-BWMW6TP | 256Kbit and 128Kbit Serial I2C Bus EEPROM With Three Chip Enable Lines |
| M24128-MW5T | 256/128 Kbit Serial IC Bus EEPROM Without Chip Enable Lines |
| M24128-BWMW6P | 256Kbit and 128Kbit Serial I2C Bus EEPROM With Three Chip Enable Lines |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M24128-WMN5T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256/128 Kbit Serial IC Bus EEPROM Without Chip Enable Lines |
| M24128-WMN6 | 功能描述:電可擦除可編程只讀存儲器 5.5V 128K (16Kx8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M24128WMN6T | 制造商:ST MICRO 功能描述:* |
| M24128-WMN6T | 制造商:STMicroelectronics 功能描述: |
| M24128-WMN6TP/P | 制造商:STMicroelectronics 功能描述:E-EPROM 128K (24128) SO 08 .15 J - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。