- 您現在的位置：買賣IC網 > PDF目錄370825 > M1MA151WKT1 (樂山無線電股份有限公司) Common Anode Silicon Dual Switching diodes PDF資料下載
參數資料
| 型號： | M1MA151WKT1 |
| 廠商： | 樂山無線電股份有限公司 |
| 英文描述： | Common Anode Silicon Dual Switching diodes |
| 中文描述： | 雙共陽極硅開關二極管 |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 85K |
| 代理商： | M1MA151WKT1 |
4
Motorola Small–Signal Transistors, FETs and Diodes Device Data
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the SC–59 package should be
the same as the pad size on the printed circuit board, i.e., a
1:1 registration.
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a
figure for belt speed. Taken together, these control settings
make up a heating “profile” for that particular circuit board.
On machines controlled by a computer, the computer
remembers these profiles from one operating session to the
next. Figure 1 shows a typical heating profile for use when
soldering a surface mount device to a printed circuit board.
This profile will vary among soldering systems but it is a good
starting point. Factors that can affect the profile include the
type of soldering system in use, density and types of
components on the board, type of solder used, and the type
of board or substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density board.
The Vitronics SMD310 convection/infrared reflow soldering
system was used to generate this profile. The type of solder
used was 62/36/2 Tin Lead Silver with a melting point
between 177–189
°
C. When this type of furnace is used for
solder reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
170
°
C
140
°
C
Figure 1. Typical Solder Heating Profile
相關PDF資料 |
PDF描述 |
|---|---|
| M1MA152AT1 | SC-59 PACKAGE SINGLE SILICON SWITCHING DIODES 40/80 V-100 mA SURFACE MOUNT |
| M1MA152WKT1 | Switch Lens; For Use With:EAO Switch Series 18 Pushbutton Switches; Lens Color:Red; Collar Shape:Square; Color:Red; Actuator Style:Square |
| M1MA152WAT1 | COMMON ANODE DUAL SWITCHING DIODES |
| M1MA152WK | COMMON CATHODE DUAL SWITCHING DIODES |
| M1MA152AT1 | SINGLE SILICON SWITCHING DIODES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M1MA151WKT1_12 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Common Cathode Silicon Dual Switching Diodes |
| M1MA151WKT1G | 功能描述:二極管 - 通用，功率，開關 SS SWCH DIO 40V TR RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube |
| M1MA151WKT2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| M1MA152A | 制造商:SECOS 制造商全稱:SeCoS Halbleitertechnologie GmbH 功能描述:Surface Mount Switching Diode |
| M1MA152AT1 | 功能描述:二極管 - 通用，功率，開關 80V 100mA RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。