- 您現在的位置：買賣IC網 > PDF目錄377800 > M-986-2A1 (Clare, Inc.) MF Transceiver PDF資料下載
參數資料
| 型號： | M-986-2A1 |
| 廠商： | Clare, Inc. |
| 英文描述： | MF Transceiver |
| 中文描述： | 中頻收發器 |
| 文件頁數： | 2/13頁 |
| 文件大?。?/td> | 499K |
| 代理商： | M-986-2A1 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
Electrical Characteristics/Temperature Range
Parameter
Test ConditionsMin
Typ
-
Max
50
Unit
75
I
CC
Supply current
f = 20.5 MHz, V
CC
= 5.5V,
mA
T
A
= 0 to 70 C
I
OH
= MAX
I
OH
= 20 μ A
I
OL
= MAX
V
CC
= MAX
V
OH
High-level output voltage
2.4
3
-
-
-
V
V
V
μA
μA
μA
μA
pF
pF
pF
pF
V
CC
-0.4
-
-
-
-
-
-
-
-
-
V
OL
I
OZ
Low-level output voltage
Off-state output current
0.3
-
-
-
-
25
15
25
10
0.6
20
-20
±20
±50
-
-
-
-
VO = 2.4 V
VO = 0.4 V
Except CLKIN
CLKIN
I
I
Input current
V
I
= V
SS
to V
CC
C
I
Input capacitance
Data bus
All others
Data bus
All others
f = 1 MHz, all other pins 0 V
C
O
Output capacitance
Supply voltage range, V
CC
Input voltage range
Output voltage range
Ambient air temperature range
Storage temperature range
-0.3 V to 7 V
-0.3 V to 15 V
-0.3 V to 15 V
0 to 150C
-45C to 150C
www.clare.com
M-986-2A1
Rev. 3
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at these or
any other conditions beyond those indicated in the opera-
tional sections of this data sheet is not implied. Exposure of
the device to the absolute maximum ratings for an extend-
ed period may degrade the device and effect its reliability.
2
Absolute Maximum Ratings Over Specified
Temperature Range
When binary input/output is selected, the M-986-2A1
encodes the received R1 MF tone pair into a 4 bit
binary format. The digital input to the M-986-2A1 that
selects the transmitted R1 MF tone pair must also be
coded in a 4 bit binary format.
Enable/Disable Channel (ENC): When a channel is
disabled, the receiver does not process its codec
input for R1 MF tones, and the transmitter does not
respond to transmit commands. If a transmit com-
mand is given while the channel is enabled, the “tone
off” command must be given before the channel is dis-
abled. Disabling the channel does not automatically
shut off the transmitter. When a channel is enabled,
the receiver and transmitter for that channel function
normally.
Long/Short KP Tone Detection Time (KPL): When
long KP tone detection is selected, the minimum on
time for the KP tone to be detected is 55 milliseconds.
When short KP tone detection is selected, the mini-
mum on time for the KP tone to be detected is 30 mil-
liseconds (the same as the minimum on time for the
rest of the MF tones).
Enable MF Tone Detection After Reception of KP
(KPEN): When this feature is enabled, MF tone detec-
tion is enabled after reception of the KP tone, and dis-
abled after reception of ST, ST1, ST2, or ST3 tones.
When this feature is disabled, MF tone detection is
always enabled. Select A or μ-law input/output (AMU)
for A-law encoding, this bit is set to a 1, for μ-law
encoding it is set to 0.
Function Description
The M-986-2A1 can be set up for various modes of
operation by writing two configuration bytes to the
coprocessor port. The format of the two configuration
bytes is shown in the Configuration Table on page 3
and the configuration options are described in the fol-
lowing paragraphs.
Configuration Options
External/Internal Codec Clock (ECLK):
If external
codec clocking is selected, an external clocking source
provides an 8 kHz transmit framing clock and an 8 kHz
receive framing clock. It also provides a serial bit clock
with a frequency that is a multiple of 8 kHz between
216 kHz and 2.496 MHz for exchange of data via the
serial ports. When internal codec clocking is selected,
the M-986-2A1 provides an 8 kHz framing clock and a
2.048 MHz serial bit clock.
2 of 6/Binary Input/Output (IOM):
When the 2-of-6
input/output is selected, the M-986-2A1 encodes the
received R1 MF tone pair into a 6-bit format, where
each bit represents one of the six possible frequencies.
A logic high level indicates the presence of a frequen-
cy. The digital input to the M-986-2A1 that selects the
transmitted R1 MF tone pair must also be coded in the
2-of-6 format.
相關PDF資料 |
PDF描述 |
|---|---|
| M-986-2A1P | MF Transceiver |
| M-986-2R2 | MFC Transceivers |
| M-986-2R2P | MFC Transceivers |
| M-991-01SMTR | Call Progress Tone Generator |
| M-991-02SM | Call Progress Tone Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M-986-2A1P | 功能描述:固態繼電器-PCB安裝 MF Transceiver, dual channel, 40xpin RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| M-986-2A1PL | 功能描述:固態繼電器-PCB安裝 MF Transceiver, dual channel, 44xpin RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| M-986-2R2 | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:MFC Transceivers |
| M-986-2R2P | 功能描述:固態繼電器-PCB安裝 MF Transceiver, dual channel, 40xpin RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| M-986-2R2PL | 功能描述:固態繼電器-PCB安裝 MF Transceiver, dual channel, 44xpin RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。