- 您現在的位置：買賣IC網 > PDF目錄369887 > LZ37C1B CMOS IMAGE SENSORS PDF資料下載
參數資料
| 型號： | LZ37C1B |
| 英文描述： | CMOS IMAGE SENSORS |
| 中文描述： | CMOS圖像傳感器 |
| 文件頁數： | 13/14頁 |
| 文件大?。?/td> | 123K |
| 代理商： | LZ37C1B |
LZ37C1B
13
PRECAUTIONS FOR CMOS IMAGE SENSORS
1. Package Breakage
In order to prevent the package from being broken,
observe the following instructions :
1) The CMOS image sensor is a precise optical
component and the package material is
ceramic.
Therefore,
Take care not to drop the device when
mounting, handling, or transporting.
Avoid giving a shock to the package.
Especially when pins are fixed to the socket
or the circuit board, small shock could break
the package more easily than when the
package isn’t fixed.
2) When mounting the package on the housing,
be sure that the package is not bent.
– If a bent package is forced into place
between a hard plate or the like, the pack-
age may be broken.
3) If any damage or breakage occurs on the sur-
face of the glass cap, its characteristics could
deteriorate.
Therefore,
Do not hit the glass cap.
Do not give a shock large enough to cause
distortion.
Do not scrub or scratch the glass surface.
– Even a soft cloth or applicator, if dry, could
cause flaws to scratch the glass.
2. Electrostatic Damage
As compared with general MOS-LSI, CMOS image
sensor has lower ESD. Therefore, take the following
antistatic measures when handling the CMOS
image sensor :
1) Always discharge static electricity by grounding
the human body and the instrument to be used.
To ground the human body, provide resistance
of about 1 M$ between the human body and
the ground to be on the safe side.
2) When directly handling the device with the
fingers, hold the part without pins and do not
touch any pin.
3) To avoid generating static electricity,
a. do not scrub the glass surface with cloth or
plastic.
b. do not attach any tape or labels.
c. do not clean the glass surface with dust-
cleaning tape.
4) When storing or transporting the device, put it in
a container of conductive material.
3. Dust and Contamination
Dust or contamination on the glass surface could
deteriorate the output characteristics or cause a
scar. In order to minimize dust or contamination on
the glass surface, take the following precautions :
1) Handle the CMOS image sensor in a clean
environment such as a cleaned booth. (The
cleanliness level should be, if possible, class
1 000 at least.)
2) Do not touch the glass surface with the fingers.
If dust or contamination gets on the glass
surface, the following cleaning method is
recommended :
Dust from static electricity should be blown
off with an ionized air blower. For anti-
electrostatic measures, however, ground all
the pins on the device before blowing off the
dust.
The contamination on the glass surface
should be wiped off with a clean applicator
soaked in isopropyl alcohol. Wipe slowly and
gently in one direction only.
– Frequently replace the applicator and do not
use the same applicator to clean more than
one device.
Note : In most cases, dust and contamination
are unavoidable, even before the device
is first used. It is, therefore, recommended
that the above procedures should be
taken to wipe out dust and contamination
before using the device.
相關PDF資料 |
PDF描述 |
|---|---|
| LZ85202 | Telecommunication IC |
| LZ921000 | ASIC |
| LZ921100 | ASIC |
| LZ921500 | ASIC |
| LZ922200 | ASIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LZ38 | 功能描述:風扇電線及配件 FINGER GRD STEEL WIRE RoHS:否 制造商:ebm-papst 類型:Finger Guard 適合風扇大小:120 mm 系列: |
| LZ39 | 功能描述:風扇電線及配件 METAL FINGER GUARD RoHS:否 制造商:ebm-papst 類型:Finger Guard 適合風扇大小:120 mm 系列: |
| LZ39V | 制造商:YEASHIN 制造商全稱:YEASHIN 功能描述:500 mW LL-34 Hermetically Sealed Glass Zener Voltage Regulators |
| LZ-3-C | 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
| LZ-3H | 制造商:FUJITSU Component Ltd 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。