- 您現在的位置：買賣IC網 > PDF目錄358967 > LZ0P3800 (Sharp Corporation) Safety Light Curtain; Control Output Type:2PNP OSSD; Number of Beams:80; Protection Height:600mm; Sensing Range Max:6m; Supply Voltage Max:24VDC; Supply Voltage:24VDC PDF資料下載
參數資料
| 型號： | LZ0P3800 |
| 廠商： | Sharp Corporation |
| 英文描述： | Safety Light Curtain; Control Output Type:2PNP OSSD; Number of Beams:80; Protection Height:600mm; Sensing Range Max:6m; Supply Voltage Max:24VDC; Supply Voltage:24VDC |
| 中文描述： | 1/4-type內置鏡頭彩色CMOS圖像傳感器的110萬像素 |
| 文件頁數： | 14/14頁 |
| 文件大?。?/td> | 110K |
| 代理商： | LZ0P3800 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁
Dust from static electricity should be blown
off with an ionized air blower. For anti-
electrostatic measures, however, ground all
the leads on the device before blowing off
the dust.
The contamination on the surface of the lens
should be wiped off with a clean
applicator
soaked in isopropyl alcohol. Wipe slowly and
gently in one direction only.
– Frequently replace the applicator and do not
use the same applicator to clean more than
one device.
Make sure there is no dust or contamination
on the lens and screw it on the lens
holder.
4. Other
1) Soldering should be manually performed within
2 seconds per pin at 400 C maximum at
soldering iron.
Use ESD-measured soldering iron
The conditions of the soldering time in which
the soldering iron touches the package.
– In case where the soldering may exceed 2
seconds per pin, resume the work
after the
device returns to normal temperature.
Do not put too much force onto the lens and
the lens holder while soldering.
Be careful not to let the soldering iron touch
the lens holder.
– Soldering can be quickly/neatly done by
laying the soldering iron so it lightly touches
the border between the package and the
circuit board and sliding it in sideways.
2) There is no guarantee of the performance of
the device which has been removed or
resoldered after being soldered once under the
conditions mentioned above.
– In case there seems to be an inferior device,
consult with our sales office before
removing
it.
3) Avoid using or storing the CMOS image sensor
at high temperature or high
humidity as it is a
precise optical component. Do not give a
mechanical shock to the CMOS image sensor.
4) Do not expose the device to strong light. For
the color device, long exposure to
strong light
will fade the color of the color filters.
PRECAUTIONS FOR BUILT-IN LENS CMOS IMAGE SENSORS
14
相關PDF資料 |
PDF描述 |
|---|---|
| LZ0P3820 | Safety Light Curtain; Light Curtain Type:Safety; Control Output Type:2PNP OSSD; Number of Beams:80; Protection Height:1200mm; Sensing Range Max:18m; Supply Voltage Max:24VDC; Supply Voltage:24VDC RoHS Compliant: NA |
| LZ1H470LR | CHIP TYPE, LOW IMPEDANCE |
| LZ1J220KR | CHIP TYPE, LOW IMPEDANCE |
| LZ21N3VS | 1/2-type Interline Color CCD Area Sensors with 2 140 k Pixels |
| LZ21N3V | 1/2-type Interline Color CCD Area Sensors with 2 140 k Pixels |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LZ0P3817 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:1/4-type Built-in Lens Color CMOS Image Sensor with 350 k Pixels |
| LZ0P3820 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:l/7-type lens-integrated CMOS Color Area Sensor for CIF |
| LZ-1.5-C | 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
| LZ-1.5H-C | 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
| LZ-1.5H-K | 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
發布緊急采購，3分鐘左右您將得到回復。