- 您現在的位置：買賣IC網 > PDF目錄369886 > LXT980AHC LAN HUB CONTROLLER PDF資料下載
參數資料
| 型號： | LXT980AHC |
| 英文描述： | LAN HUB CONTROLLER |
| 中文描述： | 局域網集線器控制器 |
| 文件頁數： | 41/96頁 |
| 文件大小： | 1309K |
| 代理商： | LXT980AHC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
LXT980/980A Dual-Speed, 5-Port Fast Ethernet Repeater
Datasheet
41
2.6.1
Serial Clock
SERCLK is a bidirectional pin; direction control is provided by the RECONFIG input. If
RECONFIG is High, the LXT980 will drive SERCLK at 625 kHz. If RECONFIG is Low,
SERCLK is an input, between 0 and 2 MHz. There is no lower bound to how slow the interface can
operate. The clock can be stopped after each operation, as long as an idle (16 ones in a row) is
transmitted first.
2.6.2
Serial Data I/O
The serial data pins, SRX and STX, should be tied together. The SRX input is compared with the
STX output. If a mismatch occurs, STX goes to a high impedance. STX is driven on the falling
edge of SERCLK. SRX is sampled on the rising edge. Refer to Test Specifications (
Figure 40 on
page 77
) for timing information.
2.6.3
Read and Write Operations
Normally the network manager directs read and write operations to a specific LXT980 device
using a two-part address consisting of HubID and ChipID. The interface allows up to 127 32-bit
registers to be read at one time. Up to two registers can be written at a time.
Some registers may be automatically cleared when subsequent write operations are performed on
other registers. Refer to the
“
Auto-Clearing Registers
”
section, which follows.
2.6.3.1
Management Frame Format
The SMI uses a simple frame format, which is shown in
Figure 11 on page 43
.
Table 19
describes
the individual fields.
Table 20 on page 43
shows how the bits for the header field would be stored
in memory, assuming that they are transmitted LSB to MSB, low address to high address.
Table 21
on page 43
lists the command set and
Table 22 on page 44
provides a variety of typical packets.
All frames begin and end with a flag of consisting of
“
01111110
”
. All fields are transmitted LSB
first. Zero-bit stuffing is required if more than five 1s in a row appear in the header, data or CRC
fields. In addition, all operations directed to the device must be followed by an idle (ten 1s in a
row), and the first operation must be preceded with an idle.
Figure 10. Typical Serial Bus Architecture
LXT918
LXT918
RMON &
Repeater MIB
Support
LXT980
8530 Serial
Controller
Network
Management
User
Definable
Partitioning
相關PDF資料 |
PDF描述 |
|---|---|
| LXT980QC | LAN HUB CONTROLLER |
| LXT9860AHC | Controller Miscellaneous - Datasheet Reference |
| LXT9860HC | Controller Miscellaneous - Datasheet Reference |
| LXT9863HC | LAN HUB CONTROLLER |
| LXT9880AGE | Controller Miscellaneous - Datasheet Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT980QC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN HUB CONTROLLER |
| LXT9860 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 10/100 Repeater with Intergrated Management |
| LXT9860AHC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| LXT9860HC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| LXT9863 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 10/100 Umnmanaged Repeater |
發布緊急采購，3分鐘左右您將得到回復。