參數資料
型號： LXT9784BE
英文描述： LAN TRANSCEIVER|OCTAL|BGA|324PIN|PLASTIC
中文描述： 網絡收發器|八路|的BGA | 324PIN |塑料
文件頁數： 38/68頁
文件大?。?/td> 1177K
代理商： LXT9784BE
LXT9784
—
Low-Power Octal PHY
38
Datasheet
2.4.1.6
10BASE-T Full Duplex
The LXT9784 PHYs support 10 Mbps full duplex by disabling the collision and the carrier sense
functions. This allows each LXT9784 PHY to transmit and receive simultaneously, achieving up to
20 Mbps of network bandwidth. The configuration is done through auto-negotiation.
2.4.2
10BASE-T Transmit
2.4.2.1
10BASE-T Manchester Encoder
When TXEN
n
is asserted, the PHY accepts di-bit data on the RMII TXD
n_
[1:0] lines, or serial
stream data on the SMII TXD
n
line. After the clocked data is serialized into a 10 Mbps serial
stream, the 20 MHz clock performs the Manchester encoding. The Manchester code always has a
mid-bit transition. If the data to be transmitted is "1", then the transition is from low to high. If the
value is "0" then the transition is from high to low. The boundary transition (such as between cell
times) occurs only when the data changes from bit to bit: if "10" then the change is from high to
low; if "01" then the change is from low to high.
10BASE-T RMII Data Transmission
The data is transferred in di-bits at a 50 MHz rate. Therefore the data on TXD
n_
[1:0] is valid for 10
clock cycles for each di-bits.
10BASE-T SMII Data Transmission
The data is signaled in ten-bit segments. Each segment is delimited by a SYNC pulse (every 10
clocks). In 10M mode, the data rate is one-tenth the 100M rate, therefore each segment is repeated
ten times so that every 10 segments represent a new byte of data.
2.4.2.2
10BASE-T Driver and Filter
Since 10BASE-T and 100BASE-TX have different filtration needs, both filters are implemented
inside the chip. This allows the two technologies to share the same magnetics. The LXT9784
supports both technologies through one pair of TPOP
n
and TPON
n
pins and by externally sharing
the same magnetics.
In 10 Mbps mode, the LXT9784 PHYs begin transmitting the serial Manchester bit stream within 3
bit times (300 ns) after the assertion TXEN
n
. In 10-Mbps mode the line drivers use a pre-distortion
algorithm to improve jitter tolerance. The line drivers reduce their drive level during the second
half of
“
wide
”
(100 ns) Manchester pulses and maintain a full drive level during all narrow (50 ns)
pulses and the first half of the wide pulses. The LXT9784
’
s advanced wave-shaping circuitry
prevents overcharging during wide pulses, a major source of jitter.
2.5
MDI/MDI-X Function
When connecting Ethernet devices together, there are two types of cables in use: straight-through
and crossed-over cables. In a typical connection, DTE to Switch, cross-over is implemented in the
Switch MAU. In this case a straight-through cable is required. However, in case that a connection
is required between two MAUs of the same type, then an external cross-over cable is required. In
相關PDF資料
PDF描述
LXT9785BC LAN TRANSCEIVER|OCTAL|BGA|241PIN|PLASTIC
LXT9785HC LAN TRANSCEIVER|OCTAL|QFP|208PIN|PLASTIC
LXT970AQC LAN TRANSCEIVER|SINGLE|CMOS|QFP|64PIN|PLASTIC
LXT970ATC Telecomm/Datacomm
LXT971ABC LAN TRANSCEIVER|SINGLE|CMOS|BGA|64PIN|PLASTIC
相關代理商/技術參數
參數描述
LXT9785 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 8-Port 10/100 Mbps PHY Transceivers
LXT9785BC 制造商:Intel 功能描述:DATACOM, ETHERNET TRANSCEIVER, PBGA241
LXT9785BC.D0 制造商:Cortina Systems Inc 功能描述:DATACOM, INTERFACE CIRCUIT, PBGA241
LXT9785HC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN TRANSCEIVER|OCTAL|QFP|208PIN|PLASTIC
LXT980AHC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN HUB CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*